Jeep Grand Cherokee WJ. Manual - part 414

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  412  413  414  415   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 414

 

 

BOOST VALVE

The boost valve (Fig. 44) provides increased fluid

apply pressure to the overdrive clutch during 3-4
upshifts (Fig. 45), and when accelerating in fourth
gear.

ACCUMULATOR

DESCRIPTION

The accumulator (Fig. 46) is a hydraulic device

that has the sole purpose of cushioning the applica-
tion of a band or clutch. The accumulator consists of
a dual–land piston and a spring located in a bore in
the transmission case. The 3–4 accumulator is
located in a housing attached to the side of the valve
body (Fig. 47).

Fig. 44 Boost Valve Before Lock-up

Fig. 45 Boost Valve After Lock-up

Fig. 46 Accumulator

1 – ACCUMULATOR PISTON
2 – PISTON SPRING

Fig. 47 3–4 Accumulator and Housing

1 – ACCUMULATOR PISTON
2 – 3–4 ACCUMULATOR HOUSING
3 – TEFLON SEALS
4 – PISTON SPRING
5 – COVER PLATE AND SCREWS

21 - 38

42RE AUTOMATIC TRANSMISSION

WJ

DESCRIPTION AND OPERATION (Continued)

OPERATION

Both the accumulator and the 3–4 accumulator

function the same. Line pressure is directed between
the lands of the piston (Fig. 48), bottoming it against
the accumulator plate. The accumulator stays in this
position after the transmission is placed into a Drive
position. When the 1–2 upshift occurs (Fig. 49), line
pressure is directed to the large end of the piston and
then to the kickdown servo. As the line pressure
reaches the accumulator, the combination of spring
pressure and line pressure forces the piston away
from the accumulator plate. This causes a balanced
pressure situation, which results in a cushioned band
application. After the kickdown servo has become
immovable, line pressure will finish pushing the
accumulator up into its bore. When the large end of
the accumulator piston is seated in its bore, the band
or clutch is fully applied.

NOTE: The accumulator is shown in the inverted
position for illustrative purposes.

PISTONS

DESCRIPTION

There are several sizes and types of pistons used in

an automatic transmission. Some pistons are used to
apply clutches, while others are used to apply bands.
They all have in common the fact that they are round
or circular in shape, located within a smooth walled
cylinder, which is closed at one end and converts fluid
pressure into mechanical movement. The fluid pres-
sure exerted on the piston is contained within the sys-
tem through the use of piston rings or seals.

OPERATION

The principal which makes this operation possible

is known as Pascal’s Law. Pascal’s Law can be stated
as: “Pressure on a confined fluid is transmitted
equally in all directions and acts with equal force on
equal areas.”

Fig. 48 Accumulator in Neutral and Drive Positions

Fig. 49 Accumulator in Second Gear Position

1 – BOTTOM IN BORE
2 – SHUTTLE VALVE

WJ

42RE AUTOMATIC TRANSMISSION

21 - 39

DESCRIPTION AND OPERATION (Continued)

PRESSURE

Pressure (Fig. 50) is nothing more than force (lbs.)

divided by area (in. or ft.), or force per unit area.
Given a 100 lb. block and an area of 100 sq. in. on
the floor, the pressure exerted by the block is: 100
lbs. 100 in. or 1 pound per square inch, or PSI as it
is commonly referred to.

PRESSURE ON A CONFINED FLUID

Pressure is exerted on a confined fluid (Fig. 51) by

applying a force to some given area in contact with
the fluid. A good example of this is a cylinder filled
with fluid and equipped with a piston that is closely
fitted to the cylinder wall. If a force is applied to the
piston, pressure will be developed in the fluid. Of

course, no pressure will be created if the fluid is not
confined. It will simply “leak” past the piston. There
must be a resistance to flow in order to create pres-
sure.

Piston

sealing

is

extremely

important

in

hydraulic operation. Several kinds of seals are used
to accomplish this within a transmission. These
include but are not limited to O–rings, D–rings, lip
seals, sealing rings, or extremely close tolerances
between the piston and the cylinder wall. The force
exerted is downward (gravity), however, the principle
remains the same no matter which direction is taken.
The pressure created in the fluid is equal to the force
applied, divided by the piston area. If the force is 100
lbs., and the piston area is 10 sq. in., then the pres-
sure created equals 10 PSI. Another interpretation of
Pascal’s Law is that regardless of container shape or
size, the pressure will be maintained throughout, as
long as the fluid is confined. In other words, the
pressure in the fluid is the same everywhere within
the container.

Fig. 50 Force and Pressure Relationship

Fig. 51 Pressure on a Confined Fluid

21 - 40

42RE AUTOMATIC TRANSMISSION

WJ

DESCRIPTION AND OPERATION (Continued)

FORCE MULTIPLICATION

Using the 10 PSI example used in the illustration

(Fig. 52), a force of 1000 lbs. can be moved with a
force of only 100 lbs. The secret of force multiplica-
tion in hydraulic systems is the total fluid contact
area employed. The illustration, (Fig. 52), shows an
area that is ten times larger than the original area.
The pressure created with the smaller 100 lb. input
is 10 PSI. The concept “pressure is the same every-
where” means that the pressure underneath the
larger piston is also 10 PSI. Pressure is equal to the
force applied divided by the contact area. Therefore,
by means of simple algebra, the output force may be
found. This concept is extremely important, as it is
also used in the design and operation of all shift
valves and limiting valves in the valve body, as well
as the pistons, of the transmission, which activate
the clutches and bands. It is nothing more than
using a difference of area to create a difference in
pressure to move an object.

PISTON TRAVEL

The relationship between hydraulic lever and a

mechanical lever is the same. With a mechanical
lever it’s a weight–to–distance output rather than a
pressure–to–area output. Using the same forces and
areas as in the previous example, the smaller piston
(Fig. 53) has to move ten times the distance required
to move the larger piston one inch. Therefore, for
every inch the larger piston moves, the smaller pis-
ton moves ten inches. This principle is true in other
instances also. A common garage floor jack is a good
example. To raise a car weighing 2000 lbs., an effort
of only 100 lbs. may be required. For every inch the
car moves upward, the input piston at the jack han-
dle must move 20 inches downward.

Fig. 52 Force Multiplication

Fig. 53 Piston Travel

WJ

42RE AUTOMATIC TRANSMISSION

21 - 41

DESCRIPTION AND OPERATION (Continued)

 

 

 

 

 

 

 

Content   ..  412  413  414  415   ..