Jeep Grand Cherokee WJ. Manual - part 1259

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1257  1258  1259  1260   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1259

 

 

Symptom:

*VTSS DOES NOT TRIP FROM RIGHT REAR DOOR

POSSIBLE CAUSES

CHECK DRBIII

t FOR RIGHT REAR DOOR AJAR RESPONSE

BCM-NO VTSS TRIP FROM RR DOOR

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, read the RR DOOR AJAR SW status.

Open the right rear door.
Does the DRBIII

t display CLOSED?

All

Yes

Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.

No

Refer to symptom RIGHT REAR DOOR AJAR CKT OPEN in the
DOOR AJAR category.
Perform VTSS VERIFICATION TEST - 1A.

539

VEHICLE THEFT/SECURITY

Symptom:

*VTSS INDICATOR INOPERATIVE

POSSIBLE CAUSES

OPEN VTSS INDICATOR FUSED B(+) SUPPLY

OPEN VTSS LED

VTSS INDICATOR DRIVER CIRCUIT OPEN

BODY CONTROL MODULE--OPEN INTERNAL VTSS DRIVER

TEST

ACTION

APPLICABILITY

1

Disconnect the Automatic Headlamp Light Sensor/VTSS LED harness connector.
Measure the voltage of the Fused B+ circuit.
Is the voltage above 10.0 volts?

All

Yes

Go To

2

No

Repair the VTSS Fused B+ circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.

2

Disconnect the Automatic Headlamp Light Sensor VTSS/LED harness connector.
Using a 12-volt test light connected to 12-volts, check the VTSS Indicator Driver
circuit.
Turn the ignition on.
With the DRB in Vehicle Theft, actuate the VTSS Indicator lamp.
Does the test light illuminate when the VTSS Indicator lamp is actuated?

All

Yes

Replace the Automatic Headlamp Light Sensor/VTSS LED as-
sembly.
Perform VTSS VERIFICATION TEST - 1A.

No

Go To

3

3

Disconnect the Automatic Headlamp Light Sensor/ VTSS LED harness connector.
Disconnect the BCM C1 harness connector.
Measure the resistance of the VTSS Indicator Driver circuit.
Is the resistance below 5.0 ohms?

All

Yes

Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.

No

Repair the VTSS Indicator Driver circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.

540

VEHICLE THEFT/SECURITY

Symptom:

WASHER FLUID SENSOR FAILURE

When Monitored and Set Condition:

WASHER FLUID SENSOR FAILURE

When Monitored:

Ignition key in run position.

Set Condition:

If the resistance of the washer fluid level sensor input to the BCM is high

causing the voltage to be above 4.8 volts for 5 seconds or more.

POSSIBLE CAUSES

VERIFYING ACTIVE DTC - WASHER FLUID SENSOR FAILURE

WASHER FLUID SWITCH CONNECTOR INSPECTION

WASHER SWITCH GROUND CIRCUIT OPEN

WASHER FLUID LEVEL SENSE SHORT TO BATTERY

BCM, WASHER FLUID LEVEL SENSE CIRCUIT OPEN

WASHER FLUID LEVEL SENSE CIRCUIT OPEN

WASHER SWITCH OPEN

BCM WASHER FLUID LEVEL SWITCH

TEST

ACTION

APPLICABILITY

1

Turn ignition on.
With the DRBIII, Erase BCM DTC’s
Turn ignition off then turn ignition on.
Turn the wiper switch to each intermittent position, then low and high speed
positions, then push the washer switch.
Wait 5 minutes before reading the BCM DTC.
With the DRBIII read BCM DTC’s.
Does the DRB show

9WASHER FLUID SENSOR FAILURE9?

All

Yes

Go To

2

No

Test Complete, code not present at this time.

2

With the DRBIII, access BCM Sensors.
Turn ignition on.
Read the Washer Fluid level switch voltage.
Is the Washer Fluid Level Switch voltage above 4.8 volts?

All

Yes

Go To

3

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

541

WINDSHIELD WIPER & WASHER

TEST

ACTION

APPLICABILITY

3

Inspect the Washer Fluid Level Switch connector.
Is the switch properly connected?

All

Yes

Go To

4

No

Repair the Washer Fluid level switch connector as necessary.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn ignition off.
Disconnect the Washer Fluid Level Switch connector.
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Washer Fluid Level Ground circuit
Is the resistance below 5 ohms?

All

Yes

Go To

5

No

Repair the open Washer Fluid Level Switch Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn ignition on.
Disconnect the BCM C2 connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect a voltmeter between the Washer Fluid Level Sense circuit and ground at the
Washer Fluid Level Switch connector.
Is there any voltage present?
Is there any voltage present?

All

Yes

Go To

6

No

Repair the Washer Fluid Level Switch circuit short to battery.
Perform BODY VERIFICATION TEST - VER 1.

NOTE: If the circuit is not shorted to battery, reinstall the BCM C2
connector.

6

Turn the ignition on.
With the DRBIII

t, access the BCM Sensors.

Read the Washer Fluid Switch voltage.
Back probe a jumper wire between the Washer Fluid Level Sense circuit at the BCM
C2 connector and ground.
Is the Washer Fluid Level Sense voltage below 1.0 volts?

All

Yes

Go To

7

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

7

Turn ignition on.
With the DRBIII, access BCM Sensors.
Connect a jumper wire between the Washer Fluid Level Sense circuit at the Washer
Fluid Level Switch connector and ground .
With the DRBIII

t, read the WASHER FLUID LEVEL SWITCH VOLTAGE.

Is the Washer Fluid level Sense voltage below 1.0

All

Yes

Replace the Washer Fluid Level Switch.
Perform BODY VERIFICATION TEST - VER 1.

No

Repair the open Washer Fluid Level Switch circuit.
Perform BODY VERIFICATION TEST - VER 1.

542

WINDSHIELD WIPER & WASHER

WASHER FLUID SENSOR FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  1257  1258  1259  1260   ..