Jeep Grand Cherokee WJ. Manual - part 1227

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1225  1226  1227  1228   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1227

 

 

Symptom:

*COURTESY LAMPS ON AT ALL TIMES (EXCEPT BOTH FRONT
DOOR COURTESY LAMPS IF EQUIP)

POSSIBLE CAUSES

JUNCTION BLOCK

BCM, COURTESY LAMPS STAY ON

COURTESY LAMP DRIVER CIRCUIT SHORTED TO GROUND

TEST

ACTION

APPLICABILITY

1

Turn ignition off.
Ensure the courtesy lamp switch is in the off position.
Remove the Body Control Module from the Junction Block.
Did the courtesy lamps turn off?

All

Yes

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn ignition off.
Ensure the courtesy lamp switch is in the off position.
Disconnect the Junction Block C-1 connector.
Measure the Courtesy Lamp Driver circuit from the Junction Block C1 connector
cavity 16 to ground.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Courtesy Lamp Driver circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Junction Block
Perform BODY VERIFICATION TEST - VER 1.

411

INTERIOR LIGHTING

Symptom:

*DRIVER DOOR COURTESY LAMP INOPERATIVE

POSSIBLE CAUSES

BULB

OPEN COURTESY LAMP DRIVER CIRCUIT

OPEN COURTESY LAMP GROUND CIRCUIT

DRIVER DOOR MODULE COURTESY LAMP

TEST

ACTION

APPLICABILITY

1

Remove and inspect the courtesy lamp bulb.
Is the Courtesy Lamp bulb open?

All

Yes

Replace the bulb.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Remove the Driver’s Door Courtesy Lamp Bulb.
Disconnect the Driver Door Module C-2 connector
Measure the Courtesy Lamp Driver circuit from the bulb connector to the Driver
Door Module C-2 connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Repair the open Courtesy Lamp Driver circuit.
Perform BODY VERIFICATION TEST - VER 1.

3

Remove the Driver’s Door Courtesy Lamp Bulb.
Disconnect the Driver Door Module C-2 connector
Measure the Courtesy Lamp Ground circuit from the bulb connector to the Driver
Door Module C-2 connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

4

No

Repair the open Courtesy Lamp Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

4

View repair options.

All

Repair

Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.

412

INTERIOR LIGHTING

Symptom:

*GLOVE BOX LAMP INOPERATIVE

POSSIBLE CAUSES

GLOVE BOX BULB

OPEN FUSED B+ CIRCUIT

GLOVE BOX SWITCH

OPEN GLOVE BOX LAMP DRIVER CIRCUIT

BCM

TEST

ACTION

APPLICABILITY

1

Remove and inspect the Glove Box Bulb.
Is the bulb OK?

All

Yes

Go To

2

No

Replace the Glove Box Bulb.
Perform BODY VERIFICATION TEST - VER 1.

2

Disconnect the glove box lamp harness connector.
Measure the voltage of the Fused B+ circuit.
Is the voltage above 10.5 volts?

All

Yes

Go To

3

No

Repair the open Fused B+ circuit.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn ignition off.
Disconnect the glove box lamp harness connector.
Disconnect the BCM C1 connector.
Measure the resistance of the Glove Box Lamp Driver circuit between the Glove Box
Lamp harness connector (cav. 2) and the BCM C1 connector (cav. 23).
Is the resistance above 5.0 ohms?

All

Yes

Go To

4

No

Repair the open Glove Box Lamp Driver circuit.
Perform BODY VERIFICATION TEST - VER 1.

4

Disconnect the glove box lamp harness connector.
Connect a test light between cavities 1 and 2 of the Glove Box Lamp harness.
Did the test light illuminate?

All

Yes

Replace the Glove Box Switch.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

5

5

View repair options

All

Repair

Replace the BCM (Body Control Module).
Perform BODY VERIFICATION TEST - VER 1.

413

INTERIOR LIGHTING

Symptom:

*HEATED SEAT SWITCH ILLUMINATION LAMP INOPERATIVE

POSSIBLE CAUSES

DRIVERS HEATED SEAT SWITCH BULB OPEN

PASSENGER HEATED SEAT SWITCH BULB OPEN

OPEN GROUND CIRCUIT (DRIVERS SIDE)

OPEN GROUND CIRCUIT (PASSENGER SIDE)

PANEL LAMPS DRIVER CIRCUIT OPEN (PASSENGER SIDE)

PANEL LAMPS DRIVER CIRCUIT OPEN (DRIVERS SIDE)

BCM

TEST

ACTION

APPLICABILITY

1

Remove and inspect the Drivers Heated Seat Switch bulb.
Is the bulb OK?

All

Yes

Go To

2

No

Replace the Drivers Heated Seat Switch bulb.
Perform BODY VERIFICATION TEST - VER 1.

2

Remove and inspect the Passenger Heated Seat Switch bulb.
Is the bulb OK?

All

Yes

Go To

3

No

Replace the Passenger Heated Seat Switch bulb.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn ignition off.
Disconnect the Drivers Heated Seat Switch connector.
Measure the resistance of the Ground circuit in the Drivers Heated Seat Switch
connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

4

No

Repair the open Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn ignition off.
Disconnect the Passenger Heated Seat Switch connector.
Measure the resistance of the Ground circuit in the Passenger Heated Seat Switch
connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

5

No

Repair the open Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

414

INTERIOR LIGHTING

 

 

 

 

 

 

 

Content   ..  1225  1226  1227  1228   ..