Jeep Grand Cherokee WJ. Manual - part 1215

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1213  1214  1215  1216   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1215

 

 

Symptom:

*CHECK GAUGES INDICATOR INOPERATIVE

POSSIBLE CAUSES

ENGINE TROUBLE CODES

DEFECTIVE BULB OR SOCKET

DEFECTIVE MIC - PRINTED CIRCUIT BOARD

TEST

ACTION

APPLICABILITY

1

Be sure there are no problems with the following; before continuing: engine
temperature, oil pressure, or battery voltage.
Using the DRB read ENGINE DTC’s.
Are there any PCM DTC’s present?

All

Yes

Refer to symptom list for problems related to DRIVEABILITY.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition from the Lock to the Run position. This will start the MIL bulb
check.
Did the

9Check Engine9 indicator light for approximately 4 seconds then go out?

All

No

Go To

3

Yes

Test Complete.

3

Remove and inspect the Check Engine bulb and socket.
Is there a problem with the bulb or socket?

All

Yes

Replace the defective bulb or socket as needed.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

4

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the instrument cluster circuit board.
Perform BODY VERIFICATION TEST - VER 1.

363

INSTRUMENT CLUSTER

Symptom:

*CLUSTER ILLUMINATION FAILURE

POSSIBLE CAUSES

CHECK DTC’S

BULBS AND SOCKETS

INSTRUMENT CLUSTER PRINTED CIRCUIT BOARD

TEST

ACTION

APPLICABILITY

1

Note: Ensure there is communication with the

(Instrument Clusterand the

(BCMbefore proceeding.
With the DRBIII

t, read 9BCM9 DTC’s.

Does the DRBIII

t display any dimming or panel lamp DTC’s?

All

Yes

Refer to symptom list for problems related to the Interior Light-
ing category.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition off.
Remove the Instrument Cluster.
Remove and test the cluster illumination bulbs and sockets.
Are the bulbs and sockets okay?

All

Yes

If there are no possible causes remaining, replace the Instrument
Cluster Printed Circuit Board.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the bulbs and sockets as necessary.
Perform BODY VERIFICATION TEST - VER 1.

364

INSTRUMENT CLUSTER

Symptom:

*CRUISE ON INDICATOR NOT OPERATING PROPERLY

POSSIBLE CAUSES

CRUISE INDICATOR ON AT ALL TIMES

ENGINE TROUBLE CODES

MIC SELF TEST

TEST

ACTION

APPLICABILITY

1

Ensure there is communication with the

9Instrument Cluster9, 9PCM9 and the 9ABS9

modules before proceeding.
While holding the

9trip/reset9 button, turn the ignition from the Lock to the Run

position. This will start the MIC self test.
Note: The Cruise indicator in the PRNDL should flash on for approximately
5 seconds during the self test.
Did the Cruise indicator come on for approximately 3 to 6 seconds?

All

Yes

Go To

2

No

Replace the Instrument Cluster Circuit Board in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

2

Does the Cruise indicator stay on when the cruise control is off?

All

Yes

Replace the Printed Circuit Board in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

Turn the ignition on.
With the DRB, read engine DTC’s.
Are there any PCM DTC’s present?

All

Yes

Refer to the Driveability category for the related symptom(s)
involving the speed control system.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

365

INSTRUMENT CLUSTER

Symptom:

*FUEL GAUGE NOT OPERATING PROPERLY

POSSIBLE CAUSES

MIC SELF TEST

ENGINE DTC’S PRESENT

DEFECTIVE GAUGE PACK

FUEL GAGE SENDING UNIT- INCORRECT

TEST

ACTION

APPLICABILITY

1

Ensure there is communication between the PCM, BCM and the Instrument Cluster
before proceeding.
During the self test all gauges should move from their minimum position to full scale
then back down to minimum again.
While holding the

9trip/reset9 button, turn the ignition from the 9off9 to the 9run9

position. This will start the MIC self test.
What were the results of the self test?

All

All gauges passed self test

Go To

2

Fuel gauge failed self test

If there are no possible causes remaining, replace the defective
Fuel Gauge Pack.
Perform BODY VERIFICATION TEST - VER 1.

All gauges failed self test

Refer to symptom list for problems related to *ALL GAUGES NOT
OPERATING.
Perform BODY VERIFICATION TEST - VER 1.

2

Using the DRB read ENGINE DTC’s.
Are there any engine DTC’s present?

All

Yes

Refer to symptoms for problems related to DRIVEABILITY
(Powertrain) information.
Perform BODY VERIFICATION TEST - VER 1.

No

Refer to Service Information for problems related to the Fuel
Gauge Sending Unit.
Perform BODY VERIFICATION TEST - VER 1.

366

INSTRUMENT CLUSTER

 

 

 

 

 

 

 

Content   ..  1213  1214  1215  1216   ..