Jeep Grand Cherokee WJ. Manual - part 1197

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1195  1196  1197  1198   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1197

 

 

Symptom:

DRIVER BLEND DOOR RANGE TOO SMALL (STORED)

When Monitored and Set Condition:

DRIVER BLEND DOOR RANGE TOO SMALL (STORED)

When Monitored:

Ignition in RUN and IOD fuse installed.

Set Condition:

This condition is set when the AZC monitors the travel range during

system initialization and the measured range is less than expected.

POSSIBLE CAUSES

AZC MODULE STORED CODES PRESENT

STORED CODES TEST COMPLETE

TEST

ACTION

APPLICABILITY

1

Note: Active codes must be resolved before diagnosing stored codes.
Anytime a code becomes active during this test, proceed to the conclusion question.
Turn the ignition on.
With the DRB, erase any stored DTC’s.
Monitor the DRB for active codes during the following test steps.
Turn the mode select switch to the panel position with the fan control on low.
Manually sweep the driver and passenger temperature control knobs from cold to hot
then back to cold.
Manually sweep the blower motor control knob through all positions.
Manually sweep the mode select switch knob through all positions.
With the DRB, perform the AZC self test.
With the DRB, actuate all of the AZC door motors.
Place the vehicle on a hoist, and raise the wheels off the floor.
Start engine. Place the transmission in drive. Brake off.
WARNING: Be sure to keep hands and feet clear of rotating wheels. Keep
clear of the engine’s moving parts
Did any AZC code become active during this test?

All

Yes

Return to the Symptom List and choose the active code.
Perform BODY VERIFICATION TEST - VER 1.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.
Perform BODY VERIFICATION TEST - VER 1.

291

HEATING & A/C

Symptom:

ENGINE COOLANT RESPONSE FAILURE (ACTIVE)

When Monitored and Set Condition:

ENGINE COOLANT RESPONSE FAILURE (ACTIVE)

When Monitored:

Every 8 seconds with the ignition on.

Set Condition:

This condition is set if the AZC does not receive the engine coolant

response message within 8 seconds.

POSSIBLE CAUSES

CHECK THE PCM FOR ANY DTCS

OBSERVE THE ECT DISPLAY IN THE INSTRUMENT CLUSTER

AUTOMATIC ZONE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB check the PCM for any DTCs.
Are any DTCs present?

All

Yes

Refer to the Powertrain Diagnostic Information.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition on.
With the DRB, enter Body, Electro/Mech Cluster (MIC), Monitor Display then PCI
Bus Engine Info and monitor the engine coolant temperature display.
Does the DRB display approximately the correct engine coolant temperature?

All

Yes

Go To

3

No

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

3

With the DRB, erase the AZC DTC’s.
Turn the ignition on, wait 1 minute, then check for any AZC DTCs.
Did this DTC reset?

All

Yes

Replace the AZC Module.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

292

HEATING & A/C

Symptom:

ENGINE COOLANT RESPONSE FAILURE (STORED)

When Monitored and Set Condition:

ENGINE COOLANT RESPONSE FAILURE (STORED)

When Monitored:

Every 8 seconds with the ignition on.

Set Condition:

This condition is set if the AZC does not receive the engine coolant

response message within 8 seconds.

POSSIBLE CAUSES

AZC MODULE STORED CODES PRESENT

STORED CODES TEST COMPLETE

TEST

ACTION

APPLICABILITY

1

Note: Active codes must be resolved before diagnosing stored codes.
Anytime a code becomes active during this test, proceed to the conclusion question.
Turn the ignition on.
With the DRB, erase any stored DTC’s.
Monitor the DRB for active codes during the following test steps.
Turn the mode select switch to the panel position with the fan control on low.
Manually sweep the driver and passenger temperature control knobs from cold to hot
then back to cold.
Manually sweep the blower motor control knob through all positions.
Manually sweep the mode select switch knob through all positions.
With the DRB, perform the AZC self test.
With the DRB, actuate all of the AZC door motors.
Place the vehicle on a hoist, and raise the wheels off the floor.
Start engine. Place the transmission in drive. Brake off.
WARNING: Be sure to keep hands and feet clear of rotating wheels. Keep
clear of the engine’s moving parts
Did any AZC code become active during this test?

All

Yes

Return to the Symptom List and choose the active code.
Perform BODY VERIFICATION TEST - VER 1.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.
Perform BODY VERIFICATION TEST - VER 1.

293

HEATING & A/C

Symptom:

ENGINE RPM FAILURE (ACTIVE)

When Monitored and Set Condition:

ENGINE RPM FAILURE (ACTIVE)

When Monitored:

Every 8 seconds with the ignition on.

Set Condition:

This condition is set if the AZC does not receive the engine RPM response

message within 8 seconds.

POSSIBLE CAUSES

CHECK THE PCM FOR ANY DTCS

OBSERVE THE RPM DISPLAY IN THE INSTRUMENT CLUSTER

AUTOMATIC ZONE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB check the PCM for any DTCs.
Are any DTCs present?

All

Yes

Refer to the Powertrain Diagnostic Information.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition on.
With the DRB, enter Body, Electro/Mech Cluster (MIC), Monitor Display then PCI
Bus Engine Info and monitor the engine RPM display.
Start the engine.
Does the DRB display approximately the correct engine RPM?

All

Yes

Go To

3

No

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

3

With the DRB, erase the AZC DTC’s.
Start the engine, wait 1 minute, then check for any AZC DTCs.
Did this DTC reset?

All

Yes

Replace the AZC Module.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

294

HEATING & A/C

 

 

 

 

 

 

 

Content   ..  1195  1196  1197  1198   ..