Jeep Grand Cherokee WJ. Manual - part 1193

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1191  1192  1193  1194   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1193

 

 

Symptom:

BLOWER SELECT SW SHORTED (STORED)

When Monitored and Set Condition:

BLOWER SELECT SW SHORTED (STORED)

When Monitored:

Ignition in RUN and IOD fuse installed.

Set Condition:

This condition is set if the AZC reads the blower switch value and it is

below 5 A/D counts.

POSSIBLE CAUSES

AZC MODULE STORED CODES PRESENT

STORED CODES TEST COMPLETE

TEST

ACTION

APPLICABILITY

1

Note: Active codes must be resolved before diagnosing stored codes.
Anytime a code becomes active during this test, proceed to the conclusion question.
Turn the ignition on.
With the DRB, erase any stored DTC’s.
Monitor the DRB for active codes during the following test steps.
Turn the mode select switch to the panel position with the fan control on low.
Manually sweep the driver and passenger temperature control knobs from cold to hot
then back to cold.
Manually sweep the blower motor control knob through all positions.
Manually sweep the mode select switch knob through all positions.
With the DRB, perform the AZC self test.
With the DRB, actuate all of the AZC door motors.
Place the vehicle on a hoist, and raise the wheels off the floor.
Start engine. Place the transmission in drive. Brake off.
WARNING: Be sure to keep hands and feet clear of rotating wheels. Keep
clear of the engine’s moving parts
Did any AZC code become active during this test?

All

Yes

Return to the Symptom List and choose the active code.
Perform BODY VERIFICATION TEST - VER 1.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.
Perform BODY VERIFICATION TEST - VER 1.

275

HEATING & A/C

Symptom:

CAL CHECKSUM FAILURE (ACTIVE)

When Monitored and Set Condition:

CAL CHECKSUM FAILURE (ACTIVE)

When Monitored:

Ignition in RUN and IOD fuse installed after a battery disconnect.

Set Condition:

This condition is set if the calibrated check sum does not match the stored

value.

POSSIBLE CAUSES

AZC - CAL CHECKSUM FAILURE

TEST

ACTION

APPLICABILITY

1

When this code is present the AZC Module must be replaced.
View repair

All

Repair

Replace the AZC Module.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

276

HEATING & A/C

Symptom:

CAL CHECKSUM FAILURE (STORED)

When Monitored and Set Condition:

CAL CHECKSUM FAILURE (STORED)

When Monitored:

Ignition in RUN and IOD fuse installed after a battery disconnect.

Set Condition:

This condition is set if the calibrated check sum does not match the stored

value.

POSSIBLE CAUSES

AZC MODULE STORED CODES PRESENT

STORED CODES TEST COMPLETE

TEST

ACTION

APPLICABILITY

1

Note: Active codes must be resolved before diagnosing stored codes.
Anytime a code becomes active during this test, proceed to the conclusion question.
Turn the ignition on.
With the DRB, erase any stored DTC’s.
Monitor the DRB for active codes during the following test steps.
Turn the mode select switch to the panel position with the fan control on low.
Manually sweep the driver and passenger temperature control knobs from cold to hot
then back to cold.
Manually sweep the blower motor control knob through all positions.
Manually sweep the mode select switch knob through all positions.
With the DRB, perform the AZC self test.
With the DRB, actuate all of the AZC door motors.
Place the vehicle on a hoist, and raise the wheels off the floor.
Start engine. Place the transmission in drive. Brake off.
WARNING: Be sure to keep hands and feet clear of rotating wheels. Keep
clear of the engine’s moving parts
Did any AZC code become active during this test?

All

Yes

Return to the Symptom List and choose the active code.
Perform BODY VERIFICATION TEST - VER 1.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.
Perform BODY VERIFICATION TEST - VER 1.

277

HEATING & A/C

Symptom:

COUNTRY CODE FAILURE (ACTIVE)

When Monitored and Set Condition:

COUNTRY CODE FAILURE (ACTIVE)

When Monitored:

Every 8 seconds with the ignition on.

Set Condition:

This condition is set if the AZC does not receive the country code message

within 8 seconds.

POSSIBLE CAUSES

COUNTRY CODE FAILURE

PROGRAM COUNTRY CODE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, enter Body, Body Computer then Module Display and observe the
country code.
Compare the country code to the VIN.
Does the country code match the VIN?

All

Yes

Replace the AZC Module.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

No

Program the correct country code into the BCM and retest
vehicle.
With the DRB, Reset Module after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.

278

HEATING & A/C

 

 

 

 

 

 

 

Content   ..  1191  1192  1193  1194   ..