Jeep Grand Cherokee WJ. Manual - part 1177

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1175  1176  1177  1178   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1177

 

 

TEST

ACTION

APPLICABILITY

9

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Disconnect the Passenger Heated Seat Back 2-way (green) connector.
Measure the resistance of the Passenger Seat Heater Ground circuit (jumper).
Is the resistance below 5.0 ohms?

All

Yes

Go To

10

No

Repair the open Driver Seat Heater Ground (jumper) circuit.
Perform VERIFICATION TEST -MEMORY SYSTEM.

10

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Back 2-way (green) connector.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Measure the resistance of the Passenger Seat Heater Ground circuit.
Connect one lead to the Passenger Seat Heater Ground circuit at the Passenger
Heated Seat Back 2-way connector and the other lead to the Passenger Seat Heater
Ground circuit in the Passenger Heated Seat Cushion 4-way connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

11

No

Repair the open Passenger Seat Heater Ground circuit between
the Passenger Heated Seat Back 2-way connector and the Pas-
senger Heated Seat Cushion 4-way connector.
Perform VERIFICATION TEST -MEMORY SYSTEM.

11

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Back 2-way (green) connector.
Disconnect the HSM C2 harness connector.
Measure the resistance of the Passenger Seat Heater Ground circuit between the
Seat Back 2-way connector (harness side) and the Heated Seat Module C2 connector.
Is the resistance below 5.0 ohms?

All

Yes

Test Complete.

No

Repair the Passenger Seat Heater Ground circuit for an open.
Perform VERIFICATION TEST -MEMORY SYSTEM.

211

ELECTRICALLY HEATED SYSTEMS

PASSENGER SEAT HEAT OUTPUT OPEN/SHT TO BATTERY (LIMITED)

Continued

Symptom:

PASSENGER SEAT HEAT OUTPUT SHORT TO GND (LIMITED)

When Monitored and Set Condition:

PASSENGER SEAT HEAT OUTPUT SHORT TO GND (LIMITED)

When Monitored:

With the ignition on, during the heated seat operation.

Set Condition:

This condition is set immediately after the Heated Seat Module detects an

output shorted to ground.

POSSIBLE CAUSES

DTC PRESENT

PASSENGER SEAT HEATER B(+) DRIVER CKT SHORTED TO GROUND

PASSENGER SEAT HEATER B(+) DRIVER CKT SHORTED TO PASSENGER SEAT HEATER
GROUND

HEATED SEAT MODULE

HEATED SEAT MODULE

PASSENGER HEATED SEAT CUSHION SHORTED TO GROUND

PASSENGER HEATED SEAT BACK SHORTED TO GROUND

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, erase DTCs.

Start the engine.
Turn the passenger seat heater on and operate in both ranges.
With the DRBIII

t, read DTCs.

Did the PASSENGER SEAT HEAT OUTPUT SHORT TO GROUND DTC return?

All

Yes

Go To

2

No

The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform VERIFICATION TEST -MEMORY SYSTEM.

2

Using the DRBIII

t, select: Body - Memory Seat Module - Erase DTC’s.

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Start the engine.
Turn the Passenger Seat Heater on and operate in both ranges.
With the DRBIII

t, read DTC’s.

Does the DRBIII

t still show Passenger Seat Heat Output Short to Gnd?

All

Yes

Go To

3

No

Go To

5

212

ELECTRICALLY HEATED SYSTEMS

TEST

ACTION

APPLICABILITY

3

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Heated Seat Module C2 harness connector.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Measure the resistance of the Passenger Seat Heater B(+) Driver circuit to the
Passenger Seat Heater Ground circuit in the HSM C2 connector.
Is the resistance below 1000.0 ohms?

All

Yes

Repair the Passenger Seat Heater B(+) Driver circuit for a short
to the Passenger Seat Heater Ground circuit.
Perform VERIFICATION TEST -MEMORY SYSTEM.

No

Go To

4

4

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Heated Seat Module C2 harness connector.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Measure the resistance of the Passenger Seat Heater B(+) Driver circuit to ground.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Passenger Seat Heater B(+) Driver circuit for a short
to ground.
Perform VERIFICATION TEST -MEMORY SYSTEM.

No

Test Complete.

5

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Measure the resistance of the Passenger Seat Heater B(+) Driver circuit in the
Passenger Heated Seat Cushion connector (cushion side) to ground.
Is the resistance below 100.0 ohms?

All

Yes

Go To

6

No

Replace the Heated Seat Module.
Perform VERIFICATION TEST -MEMORY SYSTEM.

6

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Disconnect the Passenger Heated Seat Back 2-way (black) connector.
Measure the resistance of the Passenger Seat Heater B(+) Driver circuit in the
Passenger Heated Seat Cushion connector (cushion side) to ground.
Is the resistance below 1000.0 ohms?

All

Yes

Replace the Passenger Heated Seat Cushion.
Perform VERIFICATION TEST -MEMORY SYSTEM.

No

Replace the Passenger Heated Seat Back.
Perform VERIFICATION TEST -MEMORY SYSTEM.

213

ELECTRICALLY HEATED SYSTEMS

PASSENGER SEAT HEAT OUTPUT SHORT TO GND (LIMITED) —

Continued

Symptom:

PASSENGER THERMISTOR OUT OF RANGE HIGH

When Monitored and Set Condition:

PASSENGER THERMISTOR OUT OF RANGE HIGH

When Monitored:

With the ignition on, during the heated seat operation.

Set Condition:

This condition is immediately set when the Heated Seat Module senses a

greater value than the value stored in EEPROM.

POSSIBLE CAUSES

PASSENGER SEAT SENSOR SHORTED

PASSENGER SEAT TEMPERATURE SENSOR INPUT CIRCUIT SHORTED TO BATTERY

PASSENGER SEAT TEMPERATURE SENSOR INPUT CKT SHORTED TO 5 VOLTS

HEATED SEAT MODULE - SENSOR SHORTED

SEAT SENSOR 5-VOLT SUPPLY CKT SHORTED TO GROUND

TEST

ACTION

APPLICABILITY

1

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Measure the resistance between the Seat Sensor 5 Volt Supply circuit and the
Passenger Seat Temperature Sensor Input circuit at the Passenger Heated Seat
Cushion (cushion side) connector.
Is the resistance below 800 ohms at room temperature?

All

Yes

Replace the Passenger Heated Seat Cushion - sensor shorted..
Perform VERIFICATION TEST -MEMORY SYSTEM.

No

Go To

2

2

NOTE: Raise the seat to the highest position to gain access to the connec-
tors. The HSM is located at the front of the seat and the Seat Heater
connectors are at the rear of the seat.
Turn the ignition off.
Disconnect the Heated Seat Module C1 harness connector.
Disconnect the Passenger Heated Seat Cushion 4-way connector.
Turn the ignition on.
Measure the voltage between the Passenger Seat Temperature Sensor Input circuit
and ground.
Is the voltage above 5.5 volts?

All

Yes

Repair the Passenger Seat Temperature Sensor Input circuit for a
short to battery.
Perform VERIFICATION TEST -MEMORY SYSTEM.

No

Go To

3

214

ELECTRICALLY HEATED SYSTEMS

 

 

 

 

 

 

 

Content   ..  1175  1176  1177  1178   ..