Jeep Grand Cherokee WJ. Manual - part 1166

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1164  1165  1166  1167   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1166

 

 

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Measure the resistance of the SCI Transmit circuit between the PCM C3 connector
and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

Go To

6

No

Repair the SCI Transmit circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

167

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - DIESEL ONLY —

Continued

Symptom:

*NO RESPONSE FROM PCM (SCI ONLY) - GAS ONLY

POSSIBLE CAUSES

CHECK PCM POWERS AND GROUNDS

SCI TRANSMIT CIRCUIT SHORTED TO VOLTAGE

SCI RECEIVE CIRCUIT SHORTED TO VOLTAGE

TRANSMISSION CONTROL MODULE

SCI CIRCUITS SHORTED TOGETHER

SCI TRANSMIT CIRCUIT SHORTED TO GROUND

SCI RECEIVE CIRCUIT SHORTED TO GROUND

SCI RECEIVE CIRCUIT OPEN

SCI TRANSMIT CIRCUIT OPEN

GROUND CIRCUITS AT DLC OPEN

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Perform the symptom Checking PCM Power and Ground Circuits in the Driveability
category.
Did the vehicle pass this test?

All

Yes

Go To

2

No

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Transmit circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Go To

4

3

Turn the ignition off.
Disconnect the TCM harness connector (if equipped).
NOTE: If vehicle is not equipped with a TCM, answer yes to the question.
Measure the resistance between ground and the SCI Transmit circuit.
Is the resistance below 5.0 ohms?

All

Yes

Repair the SCI Transmit circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Replace the Transmission Control Module.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

168

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Transmit circuit at the DLC connector.
Is the voltage above 1.0 volt?

All

Yes

Repair the SCI Transmit circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Go To

5

5

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Receive circuit at the DLC connector.
Is the voltage above 1.0 volt?

All

Yes

Repair the SCI Receive circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Go To

6

6

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Measure the resistance between the SCI Transmit circuit and the SCI Receive circuit
at the PCM connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair the short between the SCI Transmit and the SCI Receive
circuits.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Go To

7

7

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Receive circuit.
Is the resistance below 5.0 ohms?

All

Yes

Repair the SCI Receive circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Go To

8

8

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance of the SCI Receive circuit between the PCM C3 connector and
the DLC.
Is the resistance below 5.0 ohms?

All

Yes

Go To

9

No

Repair the SCI Receive circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

169

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - GAS ONLY —

Continued

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance of the SCI Transmit circuit between the PCM C3 connector
and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

Go To

10

No

Repair the SCI Transmit circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

10

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the negative battery cable.
Measure the resistance between ground and both ground circuits at the DLC.
Is the resistance below 5.0 ohms for each measurement?

All

Yes

Go To

11

No

Repair the ground circuit that measured above 5.0 ohms for an
open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

11

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

170

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - GAS ONLY —

Continued

 

 

 

 

 

 

 

Content   ..  1164  1165  1166  1167   ..