Jeep Grand Cherokee WJ. Manual - part 1163

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1161  1162  1163  1164   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1163

 

 

TEST

ACTION

APPLICABILITY

3

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Passenger Door Module C1 harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
Select DRB Standalone.
Select lab scope.
Select Live.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the Passenger Door Module connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

Go To

4

No

Repair the PCI Bus circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the Passenger Door Module.
Perform BODY VERIFICATION TEST - VER 1.

155

COMMUNICATION

*BUS +/- SIGNALS OPEN FROM PASSENGER DOOR MODULE —

Continued

Symptom:

*BUS +/- SIGNALS OPEN FROM SENTRY KEY IMMOBILIZER MOD-
ULE

POSSIBLE CAUSES

ATTEMPT TO COMMUNICATE WITH THE BCM

GROUND CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN

FUSED B(+) CIRCUIT OPEN

OPEN PCI BUS CIRCUIT

SENTRY KEY IMMOBILIZER MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, enter Body then Body Computer.
Was the DRB able to I/D or communicate with the BCM?

All

Yes

Go To

2

No

Refer to the symptom list for problems related to no communica-
tion with the BCM.
Perform SKIS VERIFICATION.

2

Turn the ignition off.
Disconnect the SKIM harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Repair the ground circuit for an open.
Perform SKIS VERIFICATION.

3

Turn the ignition off.
Disconnect the SKIM harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit.
Is the test light illuminated?

All

Yes

Go To

4

No

Repair the Fused Ignition Switch Output circuit for an open.
Perform SKIS VERIFICATION.

4

Turn the ignition off.
Disconnect the SKIM harness connector.
Using a 12-volt test light connected to ground, probe the Fused B(+) circuit.
Is the test light illuminated?

All

Yes

Go To

5

No

Repair the Fused B+ circuit for an open.
Perform SKIS VERIFICATION.

156

COMMUNICATION

TEST

ACTION

APPLICABILITY

5

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the SKIM harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
Select DRB Standalone.
Select lab scope.
Select Live.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the SKIM connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

Go To

6

No

Repair the PCI Bus circuit for an open.
Perform SKIS VERIFICATION.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Sentry Key Immobilizer Module in
accordance with the Service Information.
Perform SKIS VERIFICATION.

157

COMMUNICATION

*BUS +/- SIGNALS OPEN FROM SENTRY KEY IMMOBILIZER MODULE

Continued

Symptom:

*NO RESPONSE FROM AIRBAG CONTROL MODULE

POSSIBLE CAUSES

GROUND CIRCUIT OPEN

OPEN PCI BUS CIRCUIT

AIRBAG CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Warning: Turn the ignition Off, disconnect the Battery and wait 2 minutes
before proceeding.
Disconnect the Airbag Control Module harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

2

No

Repair the ground circuit for an open.
Perform AIRBAG VERIFICATION TEST - VER 1.

Note: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

2

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Turn the ignition off and wait 2 minutes before proceeding.
Disconnect the Airbag Control Module harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
Select DRB Standalone.
Select lab scope.
Select Live.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the ACM connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

Go To

3

No

Repair the PCI Bus circuit for an open.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

158

COMMUNICATION

 

 

 

 

 

 

 

Content   ..  1161  1162  1163  1164   ..