Jeep Grand Cherokee WJ. Manual - part 1155

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1153  1154  1155  1156   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1155

 

 

TEST

ACTION

APPLICABILITY

5

If there are no possible causes remaining, view Repair.

All

Repair

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

123

CHIME

CHIME INOPERATIVE WITH KEY IN IGNITION, DRIVER DOOR OPEN —

Continued

Symptom:

*CHIME INOPERATIVE AT ALL TIMES

POSSIBLE CAUSES

ACTUATES OK

BODY CONTROL MODULE - CHIME INOPERATIVE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Close all doors.
With the DRBIII

t, actuate the Chime.

Does the chime sound when actuated by the DRB?

All

Yes

If the chime operates as it should, check for other reasons that the
chime is being inoperative. Refer to symptom list for related
problems.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

124

CHIME

Symptom:

*CHIME INOPERATIVE WITH DRIVERS SEAT BELT UNFASTENED

POSSIBLE CAUSES

SEAT BELT SWITCH STATUS WRONG

SEAT BELT SWITCH OPEN

GROUND WIRE OPEN

SEAT BELT SWITCH SENSE WIRE OPEN

JUNCTION BLOCK - SEAT BELT SWITCH SENSE OPEN

BODY CONTROL MODULE -BELT SENSE OPEN

TEST

ACTION

APPLICABILITY

1

Ensure the drivers seat belt is Not fastened.
With the DRB III select: Body, Body Computer, Input Output.
Turn the ignition on.
Read the SEAT BELT SW status.
Does the DRB III show SEAT BELT SW: CLOSED?

All

Yes

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Disconnect the Seat Belt Switch connector.
Connect a jumper wire between Seat Belt Switch Sense ckt and the Ground ckt in the
Seat Belt Switch connector.
With the DRB III select: Body, Body Computer, Input Output.
Turn the ignition on.
Read the Seat Belt Sw status.
Does the DRB III show Seat Belt Sw: CLOSED?

All

Yes

Replace the Seat Belt Switch.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

Lower the Junction Block and gain access to the Junction Block C1 connector, but do
not disconnect.
Back probe a jumper wire between the Seat Belt Switch Sense circuit in the Junction
Block C1 connector cavity 19 in the upper right corner to ground.
With the DRB III select: Body, Body Computer, Input Output.
Read the Seat Belt Sw status.
Does the DRB III show Seat Belt Sw: CLOSED?

All

Yes

Repair the open Seat Belt Switch Sense wire.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

4

125

CHIME

TEST

ACTION

APPLICABILITY

4

Disconnect the Seat Belt Switch connector.
Connect a jumper wire between the Seat Belt Switch Sense circuit and chassis
ground.
With the DRB III select: Body, Body Computer, Input Output.
Read the Seat Belt Sw, status.
Does the DRB III show Seat Belt Sw: CLOSED?

All

Yes

Repair the open Ground wire.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

5

5

Turn the ignition off.
Lower the Junction Block and gain access to the Junction Block C1 connector but do
not disconnect.
Back probe a jumper wire between the Seat Belt Switch Sense circuit in the Junction
Block C1 connector cavity 19 in the upper right corner to ground.
Remove the Body Control Module from the Junction Block.
Measure the resistance between ground and the Seat Belt Switch Sense ckt in the
Junction Block - Body Control Module connector.
Is the resistance below 5.0 ohms?

All

Yes

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

126

CHIME

*CHIME INOPERATIVE WITH DRIVERS SEAT BELT UNFASTENED —

Continued

 

 

 

 

 

 

 

Content   ..  1153  1154  1155  1156   ..