Jeep Grand Cherokee WJ. Manual - part 1146

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1144  1145  1146  1147   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1146

 

 

Symptom:

IMPROPER DISK IN CD CHANGER

When Monitored and Set Condition:

IMPROPER DISK IN CD CHANGER

When Monitored:

Continuously with the ignition and CD Changer turned on.

Set Condition:

The code will set if a CD that is not formatted as a music CD is installed

in the CD Changer.

POSSIBLE CAUSES

CD CHANGER PLAY OR READ FAILURE

TEST

ACTION

APPLICABILITY

1

Replace the problem CD with a good, clean, unscratched, music CD.
Turn the radio on and select the good CD.
With the DRBIII

t, read DTC’s.

Does the DRBIII

t display CD CHANGER PLAY FAILURE, READ FAILURE, or

IMPROPER DISK IN CD CHANGER?

All

Yes

Replace the CD Changer.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

87

AUDIO

Symptom:

LEFT OUTPUT SHORT

When Monitored and Set Condition:

LEFT OUTPUT SHORT

When Monitored:

Ignition in RUN and IOD fuse installed.

Set Condition:

The radio has sensed a short on the left output for more than 10 seconds.

POSSIBLE CAUSES

DETERMINE FAULT

SPEAKER SECTION OF POWER AMPLIFIER

(+) CIRCUIT SHORTED TO GROUND

(-) CIRCUIT SHORTED TO GROUND

SPEAKER (+) & (-) CIRCUITS SHORTED TOGETHER

SPEAKER SECTION OF RADIO

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Turn the Radio on.
With the DRBIII

t, erase the audio DTC’s.

Cycle the ignition switch from off to on and wait 10 seconds.
With the DRBIII

t, read the audio DTC’s.

Does the DRBIII

t display LEFT OUTPUT SHORT?

All

Yes

Go To

2

No

Refer to the wiring diagrams located in the service information to
help isolate a possible short.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Power Amplifier C1 harness connector.
Turn the ignition on.
Turn the radio on.
With the DRBIII

t, erase the audio DTCs.

Cycle the ignition switch from off to on and wait 10 seconds.
With the DRBIII

t, read DTC’s.

Does the DRBIII

t display LEFT OUTPUT SHORT?

All

Yes

Go To

3

No

Replace the Power Amplifier.
Perform BODY VERIFICATION TEST - VER 1.

88

AUDIO

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Power Amplifier C1 harness connector.
Disconnect the Radio C2 harness connectors.
Measure the resistance between ground and each left speaker (+) circuit in the Radio
C2 connector.
Is the resistance below 1000.0 (1K) ohms?

All

Yes

Repair the left speaker (+) circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

4

4

Turn the ignition off.
Disconnect the Power Amplifier C1 harness connector.
Disconnect the Radio C1 and C2 harness connectors.
Measure the resistance between ground and each left speaker (-) circuit in the Radio
C1 and C2 connectors.
Is the resistance below 1000.0 (1K) ohms?

All

Yes

Repair the left speaker (-) circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

5

5

Turn the ignition off.
Disconnect the Power Amplifier C1 harness connector.
Disconnect the Radio C1 and C2 harness connectors.
Measure the resistance between each left speaker (+) circuit and each left speaker (-)
circuit in the radio C1 and C2 connectors.
Is the resistance below 1000.0 (1K) ohms for any of the measurements?

All

Yes

Repair the left speaker circuits shorted together.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

6

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.

89

AUDIO

LEFT OUTPUT SHORT —

Continued

Symptom:

RADIO DIMMING SHORTED HIGH

When Monitored and Set Condition:

RADIO DIMMING SHORTED HIGH

When Monitored:

Ignition in RUN and IOD fuse installed.

Set Condition:

The BCM is trying to activate the radio dimming output (park lamps on

and parade mode requested). The code will set if the BCM pulls this input low and
excessive current is sinked into the BCM.

POSSIBLE CAUSES

DIMMER SECTION OF RADIO

PANEL LAMPS DRIVER CIRCUIT SHORTED TO VOLTAGE

BODY CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Radio C1 harness connector.
Turn the ignition on.
Turn the park lamps on.
Measure the voltage of the Panel Lamps Driver circuit at the Radio C1 connector.
Rotate the dimmer switch from full low intensity to full high intensity.
Does the voltage increase from approximately 3.5 volts to approximately 12.0 volts?

All

Yes

Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition off.
Disconnect the Radio C1 harness connector.
Disconnect the BCM C1 harness connector.
Turn the ignition on.
Measure the voltage of the Panel Lamps Driver circuit at the Radio C1 connector.
Is the voltage above 1.0 volt?

All

Yes

Repair the Panel Lamps Driver circuit for a short to voltage.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

90

AUDIO

 

 

 

 

 

 

 

Content   ..  1144  1145  1146  1147   ..