Jeep Grand Cherokee WJ. Manual - part 1136

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1134  1135  1136  1137   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1136

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Remove the Airbag Run-Start Fuse.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Fused Ignition Switch Output Run-Start circuit at the
Airbag Run-Start Fuse.
Is the resistance below 5.0 ohms?

All

Yes

Go To

4

No

Replace Airbag Run-Start Fuse.
Perform AIRBAG VERIFICATION TEST - VER 1.

4

Reconnect all preciously disconnected connectors and components.
Turn ignition off.
Install a new Fused Ignition Switch Output Run-Start fuse and turn the ignition on.
Did the Fused Ignition Switch Output Run - Start circuit fuse blow?

All

Yes

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding. Replace Airbag Run - Start
Fuse.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

The Airbag RUN-START fuse was defective and has been re-
placed as part of the previous test.
Perform AIRBAG VERIFICATION TEST - VER 1.

5

WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Turn Ignition On, then reconnect the Battery.
Measure the voltage of the Fused Ignition Switch Output Run-Start Circuit at the
Airbag Control Module connector.
Is the voltage above 4.5 volts?

All

Yes

Go To

6

No

Repair open Fused Ignition Switch Output Run-Start circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.

47

AIRBAG

LOSS OF IGNITION RUN-START - ACTIVE —

Continued

TEST

ACTION

APPLICABILITY

6

WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Warning: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY TIME,
IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

48

AIRBAG

LOSS OF IGNITION RUN-START - ACTIVE —

Continued

Symptom:

NO CLUSTER MESSAGE - ACTIVE

POSSIBLE CAUSES

MIC, NO CLUSTER MESSAGE - ACTIVE

ACM, NO CLUSTER MESSAGES

TEST

ACTION

APPLICABILITY

1

Note: Ensure communications with the Mechanical Instrument Cluster.
With the DRB select PASSIVE RESTRAINTS, AIRBAG and MONITOR DISPLAY,
WARNING LAMP STATUS.
Using the DRB, read the MIC LAMP STATUS monitor.
Cycle the ignition key and observe the warning lamp monitors.
Does the DRBIII

t show MIC LAMP STATUS: ON or OFF?

All

YES

Go To

2

NO

Refer to symptom list for problems related to Instrument Cluster
communications.
Perform AIRBAG VERIFICATION TEST - VER 1.

2

WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

49

AIRBAG

Symptom:

NO PCI TRANSMISSION - STORED

When Monitored and Set Condition:

NO PCI TRANSMISSION - STORED

When Monitored:

With the ignition in the On position and the ACM transmitting

information on the PCI BUS.

Set Condition:

The code will set if the ACM cannot detect the ACM transmitting

information on the PCI BUS for 5 consecutive seconds. NOTE: Any PCI Bus Failure will
cause this code to set.

POSSIBLE CAUSES

INTERMITTENT PCI BUS TEST

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the battery is fully charged.
Active codes must be resolved before diagnosing stored codes.
Turn ignition on.
Read both active and stored codes, and record them.
With the DRB III monitor stored codes as you work through the system.
NOTE: Check for partially seat connectors and spread terminals - Clean and
repair as necessary.
Wiggle the wiring harness of each module on the PCI Bus.
While monitoring the DRB road test the vehicle.
Is there a wiring, connector problem, loss of communication or

9NO PCI TRANSMIS-

SION

9 DTC returns?

All

Yes

Repair the PCI Bus wiring, connectors or terminals as necessary.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

Test Complete.

50

AIRBAG

 

 

 

 

 

 

 

Content   ..  1134  1135  1136  1137   ..