Jeep Grand Cherokee WJ. Manual - part 1099

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1097  1098  1099  1100   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1099

 

 

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, Check the STARTS SINCE SET counter.

Note: This counter only applies to the last code set.
Is the STARTS SINCE SET counter equal to 0?

45RFE AUTO

TRANS

Yes

Go To

3

No

Go To

7

3

Turn ignition switch to the lock position
Remove the Transmission Control Relay
Turn the ignition on.
Measure the voltage at the Transmission Control Relay Output circuit in the relay
connector.
Is the voltage above 3.0 volts?

45RFE AUTO

TRANS

Yes

Repair the Transmission Control Relay Output circuit shorted to
voltage
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

4

4

Turn ignition off to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Measure the voltage at the Transmission Relay Control circuit in the relay connector.
Is the voltage above 3.0 volts?

45RFE AUTO

TRANS

Yes

Repair Transmission Relay Control circuit shorted to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

5

5

Turn the ignition to the lock position
Remove the Transmission Control Relay
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the Fused B(+) circuit and the Transmission Control
Relay Output Circuit of the relay. (Pins 30 and 87)
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Go To

6

No

Replace the Transmission Control Relay
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

6

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the TCM. WITH THE DRBIII

t PERFORM QUICK

LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

155

TRANSMISSION

P1767-TRANSMISSION RELAY ALWAYS ON —

Continued

TEST

ACTION

APPLICABILITY

7

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
Were any problems found?

45RFE AUTO

TRANS

Yes

Repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Test Complete.

156

TRANSMISSION

P1767-TRANSMISSION RELAY ALWAYS ON —

Continued

Symptom:

P1768-RELAY OUTPUT ALWAYS OFF

When Monitored and Set Condition:

P1768-RELAY OUTPUT ALWAYS OFF

When Monitored:

Continuously

Set Condition:

This code is set when less than 3 volts are present at the transmission

control relay output (pins 16,17 and 36) circuits at the Transmission Control Module
(TCM) when the TCM is energizing the relay.

POSSIBLE CAUSES

INTERMITTENT WIRING AND CONNECTORS

FUSED B+ CIRCUIT OPEN

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN

TRANSMISSION RELAY CONTROL CIRCUIT OPEN

TRANSMISSION RELAY GROUND CIRCUIT OPEN

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT SHORTED TO GROUND

TRANSMISSION RELAY CONTROL CIRCUIT SHORTED TO GROUND

TRANSMISSION CONTROL RELAY STUCK OPEN

TCM - TRANSMISSION RELAY ALWAYS OFF

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

157

TRANSMISSION

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, Check the STARTS SINCE SET counter.

Note: This counter only applies to the last code set.
Is the STARTS SINCE SET counter equal to 0?

45RFE AUTO

TRANS

Yes

Go To

3

No

Go To

11

3

Turn ignition switch to the lock position
Remove the Transmission Control Relay
Note: Check connectors - Clean/repair as necessary.
Measure the voltage at the Fused B+ circuit in the relay connector.
Is the voltage below 10.0 volts?

45RFE AUTO

TRANS

Yes

Repair the open Fused B(+) circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

4

4

Turn ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/TRS harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B(+) circuit and the Trans Relay Output
circuit in the relay connector..
Probe the Transmission Relay Output circuits in the TCM harness connector with the
test light
NOTE: Probe all three Transmission Control Relay Outputs in the TCM
harness connector.
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Does the light illuminate brightly?

45RFE AUTO

TRANS

Yes

Go To

5

No

Repair the open or high resistance Transmission Control Relay
Output circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

5

Turn ignition off to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Transmission Relay Control circuit between the relay
and the TCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the open Transmission Relay Control circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

6

158

TRANSMISSION

P1768-RELAY OUTPUT ALWAYS OFF —

Continued

 

 

 

 

 

 

 

Content   ..  1097  1098  1099  1100   ..