Jeep Grand Cherokee WJ. Manual - part 1080

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1078  1079  1080  1081   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1080

 

 

TEST

ACTION

APPLICABILITY

7

Turn ignition off to the lock position.
Disconnect the Transmission Solenoid/TRS harness connector.
Using a 12-volt test light connected to ground, back probe the Transmission Relay
Output circuit in the Solenoid/TRS harness connector..
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Does the light illuminate brightly?

45RFE AUTO

TRANS

Yes

Go To

8

No

Repair cause of unlit or dim test light. Open circuit or high
resistance in Ran Relay Output circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

8

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Transmission Solenoid/TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the OD Solenoid Control circuit and ground.
Is the resistance below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair OD Solenoid Control circuit short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

9

9

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Solenoid/TRS harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Relay
Output circuit in the Transmission Relay connector.
Ignition on, engine not running.
Measure the voltage of the OD Solenoid Control circuit in the Transmission Control
Module harness connector.
Is the voltage above 1.0 volt?

45RFE AUTO

TRANS

Yes

Repair OD Solenoid Control circuit short to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

10

10

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Transmission Control Module. WITH THE DRBIII

t

PERFORM QUICK LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

79

TRANSMISSION

P0760-OD SOLENOID CIRCUIT —

Continued

TEST

ACTION

APPLICABILITY

11

The conditions necessary to set this DTC are not present at this time. Using the
schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
Were any problems found?

45RFE AUTO

TRANS

Yes

Repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Test Complete.

80

TRANSMISSION

P0760-OD SOLENOID CIRCUIT —

Continued

Symptom:

P0765-UD SOLENOID CIRCUIT

When Monitored and Set Condition:

P0765-UD SOLENOID CIRCUIT

When Monitored:

Initially at power-up, then every 10 seconds thereafter. They will also

be tested immediately after a gear ratio or pressure switch error is detected.

Set Condition:

Three consecutive solenoid continuity test failures, or one failure if test is

run in response to a gear ratio or pressure switch error.

POSSIBLE CAUSES

RELATED RELAY DTC’S PRESENT

INTERMITTENT WIRING & CONNECTORS

TRANSMISSION RELAY OUTPUT CIRCUIT OPEN

UD SOLENOID CONTROL CIRCUIT OPEN

UD SOLENOID CONTROL CIRCUIT SHORT TO GROUND

UD SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE

UD SOLENOID INOPERATIVE

TCM - UD SOLENOID CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

81

TRANSMISSION

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, check for other transmission DTC’s.

Are any Transmission Control Relay related codes present? (P1765, P1767, or P1768)

45RFE AUTO

TRANS

Yes

Refer to symptom list and perform test for Trans Relay related
codes.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

3

3

With the DRBIII

t, Check the STARTS SINCE SET counter for P0765

Note: This counter only applies to the last code set.
Is the STARTS SINCE SET counter for P0765 set at 0?

45RFE AUTO

TRANS

Yes

Go To

4

No

Go To

11

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove the Starter Relay can cause a TCM - No Response
condition.
Install Transmission Simulator Miller tool #8333.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Observe the UD Solenoid LED on the Transmission Simulator.
With the DRBIII

t, actuate the UD Solenoid.

Did the UD Solenoid LED on the Simulator blink on and off?

45RFE AUTO

TRANS

Yes

Go To

5

No

Go To

6

5

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace Transmission Solenoid/TRS assembly.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

6

Turn ignition off to the lock position.
Disconnect the Transmission Solenoid/TRS harness connector.
Connect the test light clamp to a good ground.
Probe the Transmission Relay Output circuit in the Solenoid/TRS connector with the
test light
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Does the light illuminate brightly?

45RFE AUTO

TRANS

Yes

Go To

7

No

Repair cause of unlit or dim test light. (Open circuit or high
resistance in Trans Relay Output circuit)
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

82

TRANSMISSION

P0765-UD SOLENOID CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  1078  1079  1080  1081   ..