Jeep Grand Cherokee WJ. Manual - part 1042

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1040  1041  1042  1043   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1042

 

 

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Disconnect the PCM C2 harness connector.
Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the governor pressure sensor signal circuit in the Transmis-
sion Solenoid Assembly harness connector.
Is the voltage above 1.0 volt?

without 45RFE

AUTO TRANS

Yes

Repair the governor pressure sensor signal circuit for a short to
voltage.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

9

9

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor harness con-
nector.
Measure the resistance of the 5 volt supply circuit between the Governor Pressure/
Transmission Temperature Sensor harness connector and the Transmission Solenoid
Assembly harness connector.
Is the resistance below 5.0 ohms?

without 45RFE

AUTO TRANS

Yes

Go To

10

No

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

10

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor harness con-
nector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the governor pressure sensor signal circuit between the
Transmission Solenoid Assembly harness connector and the Governor Pressure/
Transmission Temperature Sensor harness connector.
Is the resistance below 5.0 ohms?

without 45RFE

AUTO TRANS

Yes

Go To

11

No

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

385

TRANSMISSION

P1763-GOVERNOR PRESSURE SENSOR VOLTS TOO HI —

Continued

TEST

ACTION

APPLICABILITY

11

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor harness con-
nector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the sensor ground circuit between the Transmission
Solenoid Assembly harness connector and the Governor Pressure/Transmission
Temperature Sensor harness connector.
Is the resistance below 5.0 ohms?

without 45RFE

AUTO TRANS

Yes

Go To

12

No

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

12

Turn the ignition off.
Note: The Transmission Solenoid Assembly harness connector must be
connected before proceeding.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor harness con-
nector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the governor pressure sensor signal circuit in the Governor
Pressure/Transmission Temperature Sensor harness connector.
Is the voltage above 1.0 volt?

without 45RFE

AUTO TRANS

Yes

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

13

13

Start the engine.
CAUTION: Set the parking brake.
Place the gear selector in Neutral.
With the DRBIII

t, read the governor pressure voltage.

Measure the voltage of the governor pressure sensor signal circuit by back probing at
the PCM.
Compare the voltmeter reading of the governor pressure sensor signal circuit to the
DRBIII

t Governor Pressure Sensor voltage.

Does the DRBIII

t Gov Press Sensor voltage match the governor pressure sensor

voltage on the voltmete

without 45RFE

AUTO TRANS

Yes

Go To

14

No

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

14

If there are no possible causes remaining, view repair.

without 45RFE

AUTO TRANS

Repair

Replace the Governor Pressure/Transmission Temperature Sensor
in accordance with the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

386

TRANSMISSION

P1763-GOVERNOR PRESSURE SENSOR VOLTS TOO HI —

Continued

TEST

ACTION

APPLICABILITY

15

At this time, the conditions required to set the DTC are not present.
Note: Use the Freeze Frame Data to help duplicate the conditions that set
the DTC. Pay particular attention to the DTC set conditions, such as, VSS,
MAP, ECT, and Load.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any technical service bulletins that may apply.
Were any problems found?

without 45RFE

AUTO TRANS

Yes

Repair as necessary.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Test Complete.

387

TRANSMISSION

P1763-GOVERNOR PRESSURE SENSOR VOLTS TOO HI —

Continued

Symptom:

P1764-GOVERNOR PRESSURE SENSOR VOLTS TOO LOW

When Monitored and Set Condition:

P1764-GOVERNOR PRESSURE SENSOR VOLTS TOO LOW

When Monitored:

Continuously with the key on and the engine running.

Set Condition:

This code will set if the voltage from the Governor Pressure Sensor is

below .10 volt for 8.5 seconds.

POSSIBLE CAUSES

OTHER TRANSMISSION DTC’S PRESENT

PARK NEUTRAL DTC’S PRESENT

INTERMITTENT PROBLEM

TRANSMISSION FLUID LEVEL AND CONDITION

5 VOLT SUPPLY CIRCUIT OPEN

GOV PRESS SENSOR SIGNAL CKT SHORT TO GND

GOV PRESS SENSOR SIGNAL CKT SHORT TO SENSOR GND

5 VOLT SUPPLY CIRCUIT OPEN INSIDE TRANS

GOV PRESS SENSOR SIGNAL CKT SHORT TO GND INSIDE TRANS

GOV PRESS SENSOR SIGNAL CKT SHORT TO SENSOR GND INSIDE TRANS

GOVERNOR PRESSURE SENSOR (LOW)

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read DTCs.

Is the Good Trip Counter for P-1764 displayed and equal to 0?

without 45RFE

AUTO TRANS

Yes

Go To

2

No

Go To

13

2

Turn the ignition on.
With the DRBIII

t, read DTCs.

Are any other transmission DTCs present?

without 45RFE

AUTO TRANS

Yes

Repair all other transmission DTCs before proceeding.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

3

388

TRANSMISSION

 

 

 

 

 

 

 

Content   ..  1040  1041  1042  1043   ..