Infiniti QX56 (Z62). Manual - part 1219

 

  Index      Infiniti     Infiniti QX56 (Z62) - service repair manual 2011 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1217  1218  1219  1220   ..

 

 

Infiniti QX56 (Z62). Manual - part 1219

 

 

SRC-80

< DTC/CIRCUIT DIAGNOSIS >

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000006220014

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-80, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006220015

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-80, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1074
B1075
B1076
B1077
B1078
B1079

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

B1080, B1096 DRIVER AIR BAG MODULE

SRC-81

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1080, B1096 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000006220016

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-81, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006220017

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT-I

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between combination switch (spiral cable) terminals.

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1080
B1096

DRIVER AIRBAG 
MODULE 
[SHORT]

Driver air bag module circuit are shorted to each 
other
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

SRC-82

< DTC/CIRCUIT DIAGNOSIS >

B1080, B1096 DRIVER AIR BAG MODULE

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Removal and Installation"

.

4.

CHECK SPIRAL CABLE CIRCUIT-II

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Removal and Installation"

.

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-81, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 6.

NO

>> INSPECTION END

6.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-11, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-81, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M301

10

M301

11

Not existed

M300

9

12

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Terminal

M32

28

29

Not existed

30

B1081 SEAT BELT PRE-TENSIONER RH

SRC-83

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1081 SEAT BELT PRE-TENSIONER RH

DTC Logic

INFOID:0000000006220018

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-83, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006220019

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE SEAT BELT PRE-TENSIONER

1.

Replace seat belt pre-tensioner RH. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-83, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT 

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-83, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1081

PRE-TEN FRONT RH 
[OPEN]

Seat belt pre-tensioner RH circuit is open

• Disconnection of wiring harness and open
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit

 

 

 

 

 

 

 

Content   ..  1217  1218  1219  1220   ..