Infiniti QX56 (Z62). Manual - part 89

 

  Index      Infiniti     Infiniti QX56 (Z62) - service repair manual 2011 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  87  88  89  90   ..

 

 

Infiniti QX56 (Z62). Manual - part 89

 

 

AV-210

< SYMPTOM DIAGNOSIS >

NORMAL OPERATING CONDITION

RELATED TO ROUTE CALCULATION AND VISUAL GUIDANCE

The vehicle icon is not displayed in 
the correct position.

The vehicle was transported after the ignition 
switch was pressed off, for example, by a ferry 
or car transporter.

Drive the vehicle for a while on a road where 
GPS signals can be received.

The position and direction of the vehicle icon 
may be incorrect depending on the driving en-
vironments and the levels of positioning accu-
racy of the navigation system.

This is not a malfunction. Drive the vehicle for 
a while to automatically correct the position 
and direction of the vehicle icon.

When the vehicle is traveling on a 
new road, the vehicle icon is located 
on another road nearby.

Because the new road is not stored in the map 
data, the system automatically places the vehi-
cle icon on the nearest road available.

Updated road information will be included in 
the next version of the map data.

The screen does not switch to the 
night screen even after turning on 
the headlights.

The daytime screen was set the last time the 
headlights were turned on.

Set the screen to the night screen mode using 
<Day/Night> when you turn on the headlights.

The map does not scroll even when 
the vehicle is moving.

The current location map screen is not dis-
played.

Press “MAP”.

The vehicle icon is not displayed. 

The current location map screen is not dis-
played.

Press “MAP”.

The location of the vehicle icon is 
misaligned from the actual position.

When using tire chains or replacing the tires, 
speed calculations based on the speed sensor 
may be incorrect.

Drive the vehicle for a while [at approximately 
30 km/h (19 MPH) for about 30 minutes] to 
automatically correct the vehicle icon posi-
tion.
If this does not correct the vehicle icon posi-
tion, contact an INFINITI dealer.

The map data has a mistake or is incomplete 
(the vehicle icon position is always misaligned 
in the same area).

Updated road information will be included in 
the next version of the map data.

Symptom

Possible cause

Possible solution

Symptom

Possible cause

Possible solution

Waypoints are not included in 
the auto reroute calculation.

Waypoints that you have already passed are not included in 
the auto reroute calculation.

If you want to go to that waypoint 
again, you need to edit the route.

Route information is not dis-
played.

Route calculation has not yet been performed.

Set the destination and perform route 
calculation.

You are not driving on the suggested route.

Drive on the suggested route.

Route guidance is set to off.

Turn on route guidance.

Route information is not provided for certain types of roads 
(roads displayed in gray).

This is not a malfunction.

The auto reroute calculation (or 
detour calculation) suggests 
the same route as the one pre-
viously suggested.

Route calculations took priority conditions into consider-
ation, but the same route was calculated.

This is not a malfunction.

A waypoint cannot be added.

Five waypoints are already set on the route, including ones 
that you have already passed.

A maximum of 5 waypoints can be set 
on the route. If you want to go to 6 or 
more waypoints, perform route calcu-
lations multiple times as necessary.

The suggested route is not dis-
played.

Roads near the destination cannot be calculated.

Reset the destination to a main or or-
dinary road, and recalculate the route.

The starting point and destination are too close.

Set a more distant destination.

The starting point and destination are too far away.

Divide your trip by selecting one or two 
intermediate destinations, and per-
form route calculations multiple times.

There are time restricted roads (by the day of the week, by 
time) near the current vehicle location or destination.

Set [Use Time Restricted Roads] to 
off. 

AV

NORMAL OPERATING CONDITION

AV-211

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

RELATED TO VOICE GUIDANCE

RELATED TO TRAFFIC INFORMATION

The part of the route that you 
have already passed is deleted.

A route is managed by sections between waypoints. If you 
passed the first waypoint, the section between the starting 
point and the waypoint is deleted. (It may not be deleted de-
pending on the area.)

This is not a malfunction.

An indirect route is suggested.

If there are restrictions (such as one-way streets) on roads 
close to the starting point or destination, the system may 
suggest an indirect route.

Adjust the location of the starting of 
the starting point or destination.

The system may suggest an indirect route because route 
calculation does not take into consideration some areas 
such as narrow streets (gray roads.) 

Reset the destination to a main or or-
dinary road, and recalculate the route.

The landmark information does 
not correspond to the actual in-
formation.

This may be caused by insufficient or incorrect map data.

Updated information will be included 
in the next version of the data.

The suggested route does not 
exactly connect to the starting 
point, waypoints, or destina-
tion.

There is no data for route calculation closes to these loca-
tions.

Set the starting point, waypoints and 
destination on a main road, and per-
form route calculation. 

Symptom

Possible cause

Possible solution

Symptom

Possible cause

Possible solution

Voice guidance is not available

Voice guidance is only available at certain intersections 
marked with? In some case, voice guidance is not avail-
able even when the vehicle should make a turn.

This is not a malfunction.

The vehicle has deviated from the suggested route.

Go back to the suggested route or request 
route calculation again

Voice guide is set to off.

Turn on voice guidance.

Route guidance is set to off.

Turn on voice guidance.

The guidance contact does not 
correspond to the actual condi-
tion. 

The contact of voice guidance may vary, depending on 
the types of intersections at which turn are made.

Follow all traffic rules and regulations.

Symptom

Possible cause

Possible solution

The traffic information is 
not displayed

The traffic information is not set to on.

Set the traffic information to on.

You are in an area where traffic information is not avail-
able

Scroll to an area where traffic information is avail-
able

You have not subscribed to XM NavTraffic or, your sub-
scription to XM NavTraffic has expired.

Check your subscription status of XM NavTraffic.

The map scale is set at a level where the display of icons 
is impossible.

Check that the map scale is set at a level in which 
the display of icons is possible. 

With the automatic de-
tour route search ON, 
no detour route is set to 
avoid congested areas.

There is no faster route compared to the current route, 
based on the road network and traffic information.

The automatic detour search is not intended for 
avoiding traffic jams. It searches for the fasted 
rote taking into consideration such things as traffic 
jams.

The route does not 
avoid road section with 
traffic information stat-
ing it is closed due to 
road construction.

The navigation system is designed not to avoid this 
event because the actual period of closure may differ 
from the declared roadwork period. 

Observe the actual road condition and follow the 
instructions on road for detour when necessary. If 
the road closure is for certain, use detour function 
and set the detour distance to avoid the closed 
road section.

Traffic information dis-
played differs from in-
formation from other 
media (e.g. radio).

Other media may use different information sources.

Observe the actual road conditions and regula-
tions. Always observe safe driving practices and 
follow all traffic regulations.

AV-212

< REMOVAL AND INSTALLATION >

AV CONTROL UNIT

REMOVAL AND INSTALLATION

AV CONTROL UNIT

Removal and Installation

INFOID:0000000006216377

CAUTION:

Before replacing AV control unit, perform “READ CONFIGURATION” to save or print current vehicle
specification. For details, refer to 

AV-108, "Description"

.

REMOVAL

1.

Remove cluster lid C. Refer to 

IP-13, "Exploded View"

.

2.

Remove AV control unit with a A/C auto amp. as a single unit from the body.

3.

Remove bracket screws, and then remove AV control unit.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Be sure to perform “WRITE CONFIGURATION” when replacing AV control unit.

AV

FRONT DISPLAY UNIT

AV-213

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

FRONT DISPLAY UNIT

Removal and Installation

INFOID:0000000006216378

REMOVAL

1.

Remove cluster lid D. Refer to 

IP-13, "Exploded View"

.

2.

Remove front display unit mounting screws.

3.

Disconnect front display unit connector to remove front display unit.

INSTALLATION

Install in the reverse order of removal.

 

 

 

 

 

 

 

Content   ..  87  88  89  90   ..