Infiniti M45 (Y34). Manual - part 793

 

  Index      Infiniti     Infiniti M45 (Y34) - service repair manual 2004 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  791  792  793  794   ..

 

 

Infiniti M45 (Y34). Manual - part 793

 

 

COLLISION DIAGNOSIS

SRS-59

C

D

E

F

G

I

J

K

L

M

A

B

SRS

COLLISION DIAGNOSIS

PFP:00015

For Frontal Collision

AHS000BQ

To repair the SRS, perform the following steps.
When SRS (except the front side air bag and side curtain air bag modules) is activated in a collision:
1.

Replace the diagnosis sensor unit.

2.

Remove the air bag modules (except the front side air bag modules and side curtain air bag modules),
crash zone sensor assembly, bracket and seat belt pre-tensioner assemblies.

3.

Check the SRS components using the table below:

Replace any SRS components showing visible signs of damage (dents, cracks and deformation).

4.

Install new air bag modules (except the front side air bag modules and side curtain air bag modules) crash
zone sensor assembly, bracket and seat belt pre-tensioner assemblies.

5.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-19, "SRS Operation

Check"

  for details. Ensure entire SRS operates properly.

When SRS is not activated in a collision:

1.

Check the SRS components using the table below:

Replace any SRS components showing visible signs of damage (dents, cracks and deformation).

2.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-19, "SRS Operation

Check"

  for details. Ensure entire SRS operates properly.

When only one front air bag module is activated in a collision:

1.

Replace the following components:

Diagnosis sensor unit

Crash zone sensor

Activated front air bag and seat belt pre-tensioner.

2.

Check the other SRS components using the table below. (Refer to “SRS is NOT activated”.)

Replace any SRS components showing visible signs of damage (dents, cracks and deformation).

3.

 Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-19, "SRS Operation

Check"

  for details. Ensure entire SRS operates properly.

Only one front air bag may inflate a crash, depending on the crash severity and whether the front occupants
are belted or unbelted. This does not indicate improper performance of the system. Perform self-diagnosis to
make sure the entire SRS operates properly.

SRS INSPECTION (FOR FRONTAL COLLISION)

Part

SRS is activated

SRS is NOT activated

Air bag module 
(driver or front pas-
senger air bag mod-
ule)

REPLACE
Install with new bolts.

1. Remove air bag module. Check harness cover and connectors for damage, termi-

nals for deformities, and harness for binding.

2.

Install driver air bag module into the steering wheel to check fit and alignment with 
the wheel.

Install passenger air bag module into the instrument panel to check fit with the 
instrument panel.

3. No damage found, reinstall with new bolts.

4. If damaged—REPLACE air bag modules with new special bolts.

Air bag must be deployed before disposal.

Crash zone sensor

REPLACE the crash 
zone sensor and 
bracket with new 
nuts.

1. Remove the crash zone sensor. Check harness connectors for damage, terminals 

for deformities, and harness for binding.

2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone 

sensor and bracket.

3. Install the crash zone sensor to check fit.

4. No damage found, reinstall with new bolts.

5. If damaged—REPLACE the crash zone sensor and bracket with new nuts.

SRS-60

COLLISION DIAGNOSIS

For Side Collision

AHS000BR

WHEN THE SIDE AIR BAG IS ACTIVATED IN THE SIDE COLLISION:

1.

Replace the following components:

All parts of front seatback (including front seatback frame) with front side air bag module (on the side on
which front side air bag is activated)

Curtain air bag module (on the side on which side curtain air bag is activated)

Diagnosis sensor unit

Satellite sensor (on the side on which side air bag and side curtain air bag is activated)

2.

Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).

3.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-19, "SRS Operation

Check"

 . Ensure entire SRS operates properly.

Seat belt pre-ten-
sioner assemblies

REPLACE
Install seat belt pre-
tensioner with new 
bolts.

1. Remove seat belt pre-tensioners.

Check harness cover and connectors for damage, terminals for deformities, and 
harness for binding.

2. Check belts for damage and anchors for loose mounting.

3. Check retractor for smooth operation.

4. Check seat belt adjuster for damage.

5. If no damage is found, reinstall seat belt pre-tensioner assembly with new bolts.

6. If damaged—REPLACE seat belt pre-tensioners with new bolts.

Seat belt pre-tensioners must be deployed before disposal.

Diagnosis sensor unit

REPLACE
Install with new bolts.

1. Check case for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.

3. If no damage is found, reinstall with new bolts and ground bolt.

4. If damaged—REPLACE diagnosis sensor unit with new bolts and ground bolt.

Steering wheel

1. Visually check steering wheel for deformities.

2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.

3. Install air bag module to check fit or alignment with steering wheel.

4. Check steering wheel for excessive free play.

5. If no damage is found, reinstall with nut.

6. If damaged—REPLACE.

Spiral cable

1. Visually check spiral cable and combination switch for damage.

2. Check connectors and protective tape for damage.

3. Check steering wheel for noise, binding or heavy operation.

4. If no damage is found, reinstall with screws.

5. If damaged—REPLACE.

Harness and connec-
tors

1. Check connectors for poor connection, damage, and terminals for deformities.

2. Check harness for binding, chafing, cuts, or deformities.

3. If no damage is found, reinstall the harness and connectors.

4. If damaged—REPLACE damaged section of harness. Do not attempt to repair, splice or modify any SRS 

harness.

Instrument panel

1. Visually check instrument panel for damage.

2. If no damage is found, reinstall the instrument panel.

3. If damaged—REPLACE the instrument panel with bolts.

Part

SRS is activated

SRS is NOT activated

COLLISION DIAGNOSIS

SRS-61

C

D

E

F

G

I

J

K

L

M

A

B

SRS

WHEN SRS IS NOT ACTIVATED IN THE SIDE COLLISION:

1.

Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
deformation).

2.

Conduct self-diagnosis using CONSULT-II or “AIR BAG” warning lamp. Refer to 

SRS-19, "SRS Operation

Check"

 . Ensure entire SRS operates properly.

SRS INSPECTION (FOR SIDE COLLISION)

Part

Front side air bag and 

side curtain air bag is 

activated

Front side air bag and side curtain air bag is NOT activated

(LH or RH) side cur-
tain air bag module

Replace the side cur-
tain air bag module.
(Repair the center pil-
lar inner, etc. before 
installing new one if 
damaged.)

1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on 

the collision side.

2. If damaged— Remove the side curtain air bag module.

3. Check for visible signs of damaged (tears etc.) of the side curtain air bag module.

4. Check harness and connectors for damage, and terminals for deformities.

5. If no damage is found, reinstall the side curtain air bag module with new bolts.

6. If damaged—REPLACE the side curtain air bag module with new bolts.

Air bag must be deployed before disposal.

Front (LH or RH) side 
air bag module

REPLACE all parts of 
seatback with 
deployed front side 
air bag module.

1. Check for visible signs of damage (dents, tears, deformation) of the seatback on 

the collision side.

2. Check harness and connectors for damage, and terminals for deformities.

3. If damaged—REPLACE the front seatback assembly.

Air bag must be deployed before disposal.

(LH or RH) side air 
bag (Satellite) sensor

REPLACE the side 
air bag (Satellite) sen-
sor on the collision 
side with new nuts.
(Repair the center pil-
lar inner, etc. before 
installing new one if 
damaged.)

1. Remove the side air bag (Satellite) sensor on the collision side. Check harness 

connectors for damage, terminals for deformities, and harness for binding.

2. Check for visible signs of damage (dents, cracks, deformation) of the side air bag 

(Satellite) sensor.

3. Install the side air bag (Satellite) sensor to check fit.

4. If no damage is found, reinstall the side sir bag (Satellite) sensor with new nuts.

5. If damaged—REPLACE the side air bag (Satellite) sensor with new nuts.

Diagnosis sensor unit

REPLACE the diag-
nosis sensor unit with 
the new bolts.

1. Check case and bracket for dents, cracks or deformities.

2. Check connectors for damage, and terminals for deformities.

3. If no damage is found, reinstall the diagnosis sensor unit with new bolts and ground 

bolt.

4. If damaged—REPLACE the diagnosis sensor unit with new bolts and ground bolt.

Seat belt pre-ten-
sioner assembly

1. Check if the seat belt can be extended smoothly.

If the seat belt cannot be extended smoothly,

Check for deformities of the center pillar inner.

If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

2. Remove the seat belt pre-tensioner assembly on the collision side. Check harness cover and connectors 

for damage, terminals for deformities, and harness for binding.

3. Check for visible signs of damage (dents, cracks, deformation) of the seat belt pre-tensioner assembly.

4. Check seat belt adjuster for damage.

5. If no damage is found, reinstall the seat belt pre-tensioner assembly.

6. If damaged—REPLACE the seat belt pre-tensioner assembly with new bolts.

The seat belt pre-tensioner assembly must be deployed before disposal.

SRS-62

COLLISION DIAGNOSIS

Seat with front side 
air bag

REPLACE all parts of 
front seatback 
(including front seat-
back frame)

1. Visually check the seat on the collision side.

2. Remove the seat on the collision side and check the following for damage and 

deformities.

Harness, connectors and terminals

Frame and recliner (for front and rear seat), and also adjuster and slides (for front 
seat)

3. If no damage is found, reinstall the seat.

4. If damaged—REPLACE the damaged seat parts using new bolts.

Center inner pillar

1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).

2. If damaged—REPAIR the center inner pillar.

Trim/headlining

1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the collision side.

2. If damaged—REPLACE the damaged trim parts.

Part

Front side air bag and 

side curtain air bag is 

activated

Front side air bag and side curtain air bag is NOT activated

 

 

 

 

 

 

 

Content   ..  791  792  793  794   ..