Infiniti M35/M45 Y50. Manual - part 865

 

  Index      Infiniti     Infiniti M35/M45 Y50 - service repair manual 2007 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  863  864  865  866   ..

 

 

Infiniti M35/M45 Y50. Manual - part 865

 

 

LT-5

C

D

E

F

G

H

I

J

L

M

A

B

LT

REMOVAL AND INSTALLATION  ...................... 292

Trunk Room Lamp (Upper/Lower) ........................ 292

BULB REPLACEMENT ..................................... 292
REMOVAL AND INSTALLATION  ...................... 292

ILLUMINATION ....................................................... 293

System Description  .............................................. 293

OUTLINE ........................................................... 293
ILLUMINATION OPERATION BY LIGHTING 
SWITCH ............................................................ 294
EXTERIOR LAMP BATTERY SAVER CONTROL 

. 295

CAN Communication System Description ............ 295
CAN Communication Unit  .................................... 295
Schematic ............................................................ 296
Wiring Diagram — ILL —  ..................................... 298
Glove Box Lamp ....................................................311

BULB REPLACEMENT, REMOVAL AND 
INSTALLATION ................................................. 311

Cigarette Lighter Illumination ................................ 311

BULB REPLACEMENT, REMOVAL AND 
INSTALLATION ................................................. 311

Front Ashtray Illumination ..................................... 312

BULB REPLACEMENT, REMOVAL AND 
INSTALLATION ................................................. 312

Rear Ashtray Illumination  ..................................... 312

REMOVAL AND INSTALLATION  ...................... 312
INSTALLATION ................................................. 312

BULB SPECIFICATIONS ........................................ 313

Headlamp ............................................................. 313
Exterior Lamp  ....................................................... 313
Interior Lamp/Illumination  ..................................... 313

LT-6

PRECAUTIONS

PRECAUTIONS 

PFP:00011

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

NKS003NW

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

PRECAUTIONS

LT-7

C

D

E

F

G

H

I

J

L

M

A

B

LT

General Precautions for Service Operations

NKS003NX

Never work with wet hands.

Xenon headlamp includes high voltage generating part. Be sure
to disconnect battery negative cable (negative terminal) or
power fuse before removing, installing, or touching the xenon
headlamp (including lamp bulb).

Turn the lighting switch OFF before disconnecting and connect-
ing the connector.

When turning the xenon headlamp on and while it is illuminated,
never touch the harness, bulb, and socket of the headlamp.

When checking the headlamp on/off operation, check it on vehi-
cle and with the power connected to the vehicle-side connector.

Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.

Install the xenon headlamp bulb socket correctly. If it is installed improperly, high-voltage leak or corona
discharge may occur that can melt the bulb, connector, and housing. Do not illuminate the xenon head-
lamp bulb out of the headlamp housing. Doing so can cause fire and harm your eyes.

When the bulb has burned out, wrap it in a thick vinyl bag and discard. Do not break the bulb.

Leaving the bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.

When adjusting the headlamp aiming, turn the aiming adjustment screw only in the tightening direction. (If
it is necessary to loosen the screw, first fully loosen the screw, and then turn it in the tightening direction.)

Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.

PKIB7344E

LT-8

HEADLAMP (FOR USA) - CONVENTIONAL TYPE -

HEADLAMP (FOR USA) - CONVENTIONAL TYPE -

PFP:26010

Component Parts and Harness Connector Location

NKS003NY

System Description

NKS003NZ

The control of the headlamp system operation is dependent upon the position of the combination switch (light-
ing switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives
input signal requesting the headlamps (and tail lamps) illuminate. This input signal is communicated to the
IPDM E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU
(central processing unit) located in the IPDM E/R controls the headlamp high and headlamp low relay coils.
These relays, when energized, direct power to the respective headlamps, which then illuminate. 

PKIC1983E

 

 

 

 

 

 

 

Content   ..  863  864  865  866   ..