Infiniti M35/M45 Y50. Manual - part 780

UPPER LINK

FSU-17

[2WD]

C

D

F

G

H

I

J

K

L

M

A

B

FSU

●

Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to 

BRC-6, "Adjust-

ment of Steering Angle Sensor Neutral Position"

 .

FSU-18

[2WD]

STABILIZER BAR

STABILIZER BAR

PFP:54611

Removal and Installation

NES000II

REMOVAL

1.

Remove tires from vehicle with a power tool.

2.

Remove undercover with a power tool. 

3.

Remove the mounting nut on the lower side of stabilizer connecting rod with a power tool, and then
remove stabilizer connecting rod from stabilizer bar.

4.

If necessary remove the mounting nut on the upper side of stabilizer connecting rod with a power tool, and
then remove stabilizer connecting rod from transverse link.

5.

Remove the mounting nuts of stabilizer clamp, and then remove stabilizer clamp and stabilizer bushing.

6.

Remove stabilizer bar from vehicle.

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.

INSTALLATION

Installation is the reverse order of removal. For tightening torque, refer to 

FSU-8, "Components"

 .

SERVICE DATA AND SPECIFICATIONS (SDS)

FSU-19

[2WD]

C

D

F

G

H

I

J

K

L

M

A

B

FSU

SERVICE DATA AND SPECIFICATIONS (SDS)

PFP:00030

Wheel Alignment (Unladen *)

NES000IJ

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

NES000IK

Tire size

245/45R18

245/40R19

Camber
Degree minute (Decimal degree)

Minimum

–1

°

 00

′

 (–1.00

°

)

Nominal

–0

°

 15

′

 (–0.25

°

)

Maximum

0

°

 30

′

 (0.50

°

)

Left and right difference

33

′

 (0.55

°

) or less

Caster
Degree minute (Decimal degree)

Minimum

3

°

 45

′

 (3.75

°

)

3

°

 50

′

 (3.83

°

)

Nominal

4

°

 30

′

 (4.50

°

)

4

°

 35

′

 (4.58

°

)

Maximum

5

°

 15

′

 (5.25

°

)

5

°

 20

′

 (5.33

°

)

Left and right difference

39

′

 (0.65

°

) or less

Kingpin inclination
Degree minute (Decimal degree)

Minimum

6

°

 30

′

 (6.50

°

)

Nominal

7

°

 15

′

 (7.25

°

)

Maximum

8

°

 00

′

 (8.00

°

)

Total toe-in

Distance

Minimum

 0 mm (0 in)

Nominal

In 1 mm (0.04 in)

Maximum

In 2 mm (0.08 in)

Angle (left wheel or right wheel)
Degree minute (Decimal degree)

Minimum

0

′

 (0

°

)

Nominal

In 3

′

 (0.05

°

)

Maximum

In 6

′

 (0.10

°

)

Swing torque

Transverse link

0.5 - 3.6 N·m (0.06 - 0.36 kg-m, 5 - 31 in-lb)

Upper link

0 - 2.0 N·m (0 - 0.2 kg-m, 0 - 17 in-lb)

Measurement on spring balance

Transverse link

7.8 - 56.3 N (0.8 - 5.7 kg, 1.8 - 12.5 lb)

Upper link

0 - 61.5 N (0 - 6.2 kg, 0 - 13.6 lb)

Rotating torque

Transverse link

0.5 - 3.9 N·m (0.06 - 0.39 kg-m, 5 - 34 in-lb)

Upper link

0 - 2.0 N·m (0 - 0.2 kg-m, 0 - 17 in-lb)

Axial end play

0 mm (0 in)

FSU-20

[2WD]

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheelarch Height (Unladen*)

NES000IL

*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Tire size

245/45R18

245/40R19

Front (Hf)

USA

717 mm (28.23 in)

721 mm (28.39 in)

CANADA

718 mm (28.27 in)

Rear (Hr)

USA

710 mm (27.95 in)

711 mm (27.99 in)

CANADA

711 mm (27.99 in)

SFA818A