Infiniti M35/M45 Y50. Manual - part 457

DTC P0139, P0159 HO2S2

EC-301

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

Wiring Diagram

NBS004XO

BANK 1

TBWT1473E

EC-302

[VQ35DE]

DTC P0139, P0159 HO2S2

Specification data are reference values and are measured between each terminal and ground.

CAUTION:

Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.

TER-

MINAL 

NO.

WIRE 

COLOR

ITEM

CONDITION

DATA (DC Voltage)

25

P/B

Heated oxygen sensor 2 
heater (bank 1)

[Engine is running]

●

Engine speed: Below 3,600 rpm after the 
following conditions are met

–

Engine: After warming up

–

Keeping the engine speed between 3,500 
and 4,000 rpm for 1 minute and at idle for 1 
minute under no load

0 - 1.0V

[Ignition switch: ON]

●

Engine stopped

[Engine is running]

●

Engine speed: Above 3,600 rpm

BATTERY VOLTAGE
(11 - 14V)

74

W

Heated oxygen sensor 2 
(bank 1)

[Engine is running]

●

Revving engine from idle to 3,000 rpm 
quickly after the following conditions are met

–

Engine: After warming up

–

Keeping the engine speed between 3,500 
and 4,000 rpm for 1 minute and at idle for 1 
minute under no load

0 - Approximately 1.0V

78

B

Sensor ground
(Heated oxygen sensor)

[Engine is running]

●

Warm-up condition

●

Idle speed

Approximately 0V

DTC P0139, P0159 HO2S2

EC-303

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

BANK 2

TBWT1474E

EC-304

[VQ35DE]

DTC P0139, P0159 HO2S2

Specification data are reference values and are measured between each terminal and ground.

CAUTION:

Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.

Diagnostic Procedure

NBS004XP

1. 

CHECK GROUND CONNECTIONS

1.

Turn ignition switch OFF.

2.

Loosen and retighten two ground screws on the body.
Refer to 

EC-160, "Ground Inspection"

 .

OK or NG

OK

>> GO TO 2.

NG

>> Repair or replace ground connections.

TER-

MINAL 

NO.

WIRE 

COLOR

ITEM

CONDITION

DATA (DC Voltage)

6

R/L

Heated oxygen sensor 2 
heater (bank 2)

[Engine is running]

●

Engine speed: Below 3,600 rpm after the 
following conditions are met

–

Engine: After warming up

–

Keeping the engine speed between 3,500 
and 4,000 rpm for 1 minute and at idle for 1 
minute under no load

0 - 1.0V

[Ignition switch: ON]

●

Engine stopped

[Engine is running]

●

Engine speed: Above 3,600 rpm

BATTERY VOLTAGE
(11 - 14V)

55

W

Heated oxygen sensor 2 
(bank 2)

[Engine is running]

●

Revving engine from idle to 3,000 rpm 
quickly after the following conditions are met

–

Engine: After warming up

–

Keeping the engine speed between 3,500 
and 4,000 rpm for 1 minute and at idle for 1 
minute under no load

0 - Approximately 1.0V

78

B

Sensor ground
(Heated oxygen sensor)

[Engine is running]

●

Warm-up condition

●

Idle speed

Approximately 0V

1.

Body ground M70

2.

Body ground M16

PBIB2782E