Infiniti M35/M45 Y50. Manual - part 373

 

  Index      Infiniti     Infiniti M35/M45 Y50 - service repair manual 2007 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  371  372  373  374   ..

 

 

Infiniti M35/M45 Y50. Manual - part 373

 

 

LANE DEPARTURE WARNING SYSTEM

DI-75

C

D

E

F

G

H

I

J

L

M

A

B

DI

LANE DEPARTURE WARNING SYSTEM 

PFP:28442

Precautions for Lane Departure Warning (LDW) system

NKS003VF

WARNING:

Lane Departure Warning (LDW) is only a warning device to inform the driver of an unintended lane
departure. It will not steer the vehicle or prevent loss of control. It is the driver's responsibility to stay
alert, drive safely, keep the vehicle in the traveling lane, and be in control of the vehicle at all times.

LDW system does not operate under the following conditions:

At speeds below approx. 72 km/h (45 MPH).

If it cannot detect lane markers.

LDW system may not function properly under the following conditions:

On roads where a water puddle, dirt or snow is covering the lane markers.

On roads where the lane markers are faded or are not painted clearly.

On roads where the lane markers are painted yellow.

LDW system may not monitor the lane markers in certain road, weather or driving conditions.

On roads where there are sharp curves.

Where the traveling lane merges or separates.

On roads where the discontinued lane markers are present, such as near tollgates, etc.

On roads where there are not general lane markers.

On roads where the lane width is too narrow.

During bad weather (rain, fog, snow, etc.).

When strong light (for example, at sunrise or sunset) is directly shining on the front of the vehicle.

When entering or exiting a tunnel where sudden changes in brightness occur.

When traveling close to the vehicle in front of you, which causes obstruction of the camera unit
range.

When the vehicle's traveling direction does not align with the lane marker.

When rain, snow or dirt adhere to the windshield in front of the camera unit.

Excessive noise interferes with warning system chime sound and the chime may not be heard.

CAUTION:

To keep the LDW system operating properly, be sure to observe the following:

Always keep the windshield clean. The sensing capability of the camera unit depends on the con-
dition of the windshield. See “Appearance and care” for cleaning instruction.

Never strike or damage the areas around the camera unit.

Never touch the camera lens.

Never attach a sticker (including transparent material) or install an accessory near the camera
unit.

Never place reflective materials, such as a white paper or mirrors on the instrument panel. Reflec-
tion of the sunlight may adversely affect the camera unit's lane marker detection capability.

System Description

NKS003VG

LDW SYSTEM OPERATION

The Lane Departure Warning (LDW) system warns the driver when the vehicle is traveling close to either
the left or the right of the traveling lane.

The system monitors lane markers of the traveling lane using the LDW camera unit. When the LDW cam-
era unit detects that the vehicle is traveling close to either the left or the right of the traveling lane, the
LDW indicator lamp flashes and a chime sounds to alert the driver.

NOTE:
When activating turn signal, LDW system does not give a warning to the lane marker on the turn signal
side.

The LDW system can be turned on or off by pushing the LDW switch. When the system is on, the LDW
system ON indicator illuminates.

The LDW system has an automatic mode and manual mode.

DI-76

LANE DEPARTURE WARNING SYSTEM

In the automatic mode

LDW system automatically turns on, when the ignition switch is turned to the ON position. 

LDW system ON indicator located on the LDW switch illuminates, indicating that the system is on.

To cancel LDW system, push the LDW switch to turn off LDW system ON indicator. 

To turn on the system, push LDW switch again.

In the manual mode

LDW system is still off when the ignition switch is turned to the ON position.

The LDW switch must be pushed to turn on the system.

To the change modes

Push and hold LDW switch for more than 4 seconds, when LDW system ON indicator is off.

Then LDW chime sounds and blinking of LDW system ON indicator informs that the mode change is com-
pleted.

Temporary disabled status at high temperature

If the vehicle is parked in direct sunlight under high temperature conditions [approximately over 104 

°

F (40

°

C)] and then started, the LDW system may sound a chime and cancel automatically. Then LDW system

ON indicator will blink.

When the interior temperature is reduced, the system will resume to operate automatically and the LDW
system ON indicator illuminates.

Warning Function

SKIB1783E

LANE DEPARTURE WARNING SYSTEM

DI-77

C

D

E

F

G

H

I

J

L

M

A

B

DI

System Diagram

Components Description

NOTE:
*: This indicates in a few seconds for the system check during ignition switch ON.

POWER SUPPLY AND GROUND CIRCUIT

With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12, located in the fuse block (J/B)]

to LDW camera unit terminal 1.

Ground is supplied

to LDW camera unit terminals 6 and 12

through grounds M16 and M70.

Action Test

NKS003VH

LDW SYSTEM RUNNING TEST

WARNING:

Be careful when performing road test.

Understand “Precautions” and “System Description” well before the road test. Refer to 

DI-75,

"Precautions for Lane Departure Warning (LDW) system"

  an

DI-75, "System Description"

 .

Function Check

Check the LDW system operation according to the condition that the warning function works. Refer to 

DI-75,

"LDW SYSTEM OPERATION"

 .

PKIC0698E

Component

Description

LDW camera unit

Detects the lane marker by the built-in camera, gives judgement for the warning according to the 
result of detection and signals from each unit, and transmits the operation signal to LDW chime and 
LDW indicator lamp.

LDW switch

Selects ON/OFF of the system.

Indicates ON/OFF of the signal with LDW system ON indicator.

LDW chime

Gives a warning chime according to the direction from LDW camera unit.

LDW indicator lamp

Installed in combination meter, and indicates the system condition.

Blinks when LDW system is functioning to alert the driver.

Stays on when LDW system is malfunctioning.

*

BCM

Transmits turn indicator signal to LDW camera unit with CAN communication signal.

ABS actuator and electric unit 
(control unit)

Transmits vehicle speed signal to LDW camera unit with CAN communication signal.

TCM 

Transmits vehicle speed signal to LDW camera unit with CAN communication signal. (For detecting 
incorrect speed.)

DI-78

LANE DEPARTURE WARNING SYSTEM

Camera Aiming Adjustment

NKS003VI

OUTLINE

Adjust the camera aiming every time the LDW camera unit is removed or installed.

CAUTION:

Place the vehicle on the level ground when the camera aiming adjustment is operated.

Follow the CONSULT-II when adjusting the camera aiming. (Camera aiming adjustment cannot be
operated without CONSULT-II.)

PREPARATION

Keep all tires inflated to correct pressures. Adjust the tire pressure to the specified pressure value.

There is no-load in vehicle. Check if coolant, engine oil are filled up to correct level and fuel tank is full.

Shift the gear into “P” position and release the parking brake.

Clean the windshield.

NOTE:
Do not place anything reflective on the upper surface of instrument panel.

TARGET SETTING
Preparation Aiming Adjustment Jig

For aiming adjustment, prepare the following jigs and targets.

PKIB4693E

 

 

 

 

 

 

 

Content   ..  371  372  373  374   ..