Infiniti M35/M45 Y50. Manual - part 1

 

  Index      Infiniti     Infiniti M35/M45 Y50 - service repair manual 2007 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



  

 

Content   ..  1  2  3   ..

 

 

Infiniti M35/M45 Y50. Manual - part 1

 

 

ACC-2

PRECAUTIONS

PRECAUTIONS

PFP:00001

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

NBS005RO

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

●

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

●

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

●

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

ACCELERATOR CONTROL SYSTEM

ACC-3

C

D

E

F

G

H

I

J

K

L

M

A

ACC

ACCELERATOR CONTROL SYSTEM

PFP:18005

Components

NBS005RP

Removal and Installation

NBS005RQ

REMOVAL

1.

Disconnect accelerator pedal position sensor harness connector.

2.

Remove front kicking plate and dash side finisher. Refer to 

EI-37, "BODY SIDE TRIM"

 .

3.

Remove the cap and the inside mounting nut, and then disassemble the accelerator pedal pad from the
floor carpet.

4.

Press the pin (1) with long-nose pliers and pull them out in the
direction shown by the arrow (

). Then remove the accelerator

pedal pad (2).

CAUTION:

Do not disengage the part (the link) other than pins.

5.

Remove accelerator pedal stopper cover.

1.

Accelerator pedal bracket and lever 
assembly

2.

Accelerator pedal stopper cover

3.

Cap

4.

Accelerator pedal pad

5.

Pin

PBIC3203E

KBIA3594J

ACC-4

ACCELERATOR CONTROL SYSTEM

6.

Pull up the floor carpet.

7.

Remove mounting nuts of accelerator pedal bracket.

8.

Remove accelerator pedal bracket and lever assembly.

CAUTION:

●

Do not disassemble accelerator lever. Do not remove accelerator pedal position sensor from
accelerator lever.

●

Avoid impact from dropping etc. during handling.

●

Be careful to keep accelerator lever away from water.

INSTALLATION

Installation is the reverse order of removal.

INSPECTION AFTER INSTALLATION

●

Make sure accelerator pedal moves smoothly within the whole operation range when it is fully depressed
and released.

●

Make sure accelerator pedal securely returns to the fully released position.

●

For the electrical inspection of accelerator pedal position sensor, refer to the following.

–

VQ35DE

EC-617, "DTC P2122, P2123 APP SENSOR"

.

–

VK45DE

EC-1336, "DTC P2122, P2123 APP SENSOR"

.

CAUTION:

When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
ator Pedal Released Position Learning”. Refer to 

EC-86, "Accelerator Pedal Released Position

Learning"

 (VQ35DE) or 

EC-788, "Accelerator Pedal Released Position Learning"

 (VK45DE).

 

 

 

 

 

 

 

 

 

Content   ..  1  2  3   ..