Infiniti G35 (V35) Sedan. Manual - part 821

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  819  820  821  822   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 821

 

 

INT-8

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000000960429

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000000960430

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Precaution for Work

INFOID:0000000000960431

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operation.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J

PREPARATION

INT-9

< PREPARATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000000960432

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000000960433

Tool number
(Kent-Moore No.)
Tool name

Description

(J-39570)
Chassis ear

Location the noise

(J-43980)
NISSAN Squeak and Rattle 
Kit

Repairing the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Location the noise

Power tool

SIIA0995E

PIIB1407E

INT-10

< ON-VEHICLE REPAIR >

DOOR FINISHER

ON-VEHICLE REPAIR

DOOR FINISHER

Exploded View

INFOID:0000000000960434

Removal and Installation

INFOID:0000000000960435

REMOVAL

FRONT AND REAR DOOR FINISHER

1.

Fully open door window.

1.

Power window switch finisher (front)

2.

Inside handle escutcheon

3.

Front door finisher

4.

Step lamp

5.

Grommet

6.

Front door panel

7.

Power window switch finisher (rear) 

8.

Rear door finisher

9.

Rear door panel

10. Seat memory switch

Clip

Pawl

Metal clip

JMJIA0066GB

DOOR FINISHER

INT-11

< ON-VEHICLE REPAIR >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

2.

Remove inside handle escutcheon (1) with remover tool (A).

3.

Remove screw (A), located on the back side of inside handle
escutcheon.

4.

Pull up power window switch finisher (1) with remover tool (A).

5.

Disconnect power window switch connector, and then remove
power window switch finisher.

6.

Remove screws (A), located on the back side of power window
finisher.

7.

Remove step lamp (1). Refer to 

INL-100, "Removal and Installa-

tion"

.

: Pawl

JMJIA0073GB

JMJIA0074GB

: Pawl

JMJIA0075GB

JMJIA0076GB

JMJIA0077GB

 

 

 

 

 

 

 

Content   ..  819  820  821  822   ..