Infiniti G35 (V35) Sedan. Manual - part 720

FRONT STABILIZER

FSU-37

< ON-VEHICLE REPAIR >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

FRONT STABILIZER

Exploded View

INFOID:0000000000957808

Refer to 

FSU-39, "Exploded View"

.

Removal and Installation

INFOID:0000000000957809

REMOVAL

1.

Remove tires with power tool.

2.

Remove under cover with power tool.

3.

Remove the mounting nut on the lower side of stabilizer connecting rod with power tool, and then remove
stabilizer connecting rod from stabilizer bar.

4.

Remove the mounting nuts of stabilizer clamp, and then remove stabilizer clamp and stabilizer bushing.

5.

Remove stabilizer bar.

INSTALLATION

Install in the reverse order of removal.

Inspection

INFOID:0000000000957810

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.

FSU-38

< ON-VEHICLE REPAIR >

[AWD]

FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER

Exploded View

INFOID:0000000000957811

Refer to 

FSU-39, "Exploded View"

.

Removal and Installation

INFOID:0000000000957812

REMOVAL

1.

Remove tire with power tool.

2.

Remove under cover with power tool.

3.

Remove front cross bar.

4.

Separate steering gear assembly and lower joint. Refer to 

ST-27, "2WD : Removal and Installation"

.

5.

Remove steering outer socket from steering knuckle. Refer to 

ST-34, "AWD : Removal and Installation"

.

6.

Remove wheel sensor from steering knuckle. Refer to 

BRC-101, "REAR SENSOR ROTOR : Removal

and Installation"

.

7.

Remove shock absorber. Refer to 

FSU-29, "Removal and Installation"

.

8.

Remove front stabilizer. Refer to 

FSU-17, "Removal and Installation"

.

9.

Install engine slinger, and then hoist engine.

10. Remove transverse link from front suspension member with power tool. Refer to 

FSU-13, "Removal and

Installation"

.

11. Remove steering hydraulic piping bracket and steering gear from front suspension member. Refer to 

ST-

55, "2WD : Exploded View"

.

12. Set suitable jack front suspension member.
13. Remove mounting nuts between engine mounting insulator and from suspension member. Refer to 

EM-

82, "AWD : Removal and Installation"

. 

14. Remove mounting bolts and nuts of front suspension member with power tool.
15. Gradually lower jack to remove front suspension assembly from vehicle.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-

ber bushing) under unladen condition with tires on level ground.

Inspection

INFOID:0000000000957813

INSPECTION AFTER REMOVAL

Check the front suspension member for significant deformation, cracks, or damages. Replace if necessary.

INSPECTION AFER INSTALLATION

• Check wheel alignment. Refer to  

FSU-41, "Wheel Alignment"

.

• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to 

BRC-8,

"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"

.

FRONT SUSPENSION ASSEMBLY

FSU-39

< REMOVAL AND INSTALLATION >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

REMOVAL AND INSTALLATION

FRONT SUSPENSION ASSEMBLY

Exploded View

INFOID:0000000000957814

JPEIA0002GB

FSU-40

< REMOVAL AND INSTALLATION >

[AWD]

FRONT SUSPENSION ASSEMBLY

Removal and Installation

INFOID:0000000000957815

REMOVAL

Remove suspension assembly with engine assembly from vehicle. Refer to 

EM-82, "AWD : Removal and

Installation"

.

INSTALLATION

Install in the reverse order of removal.

Inspection

INFOID:0000000000957816

INSPECTION AFTER REMOVAL

• Check wheel alignment. Refer to 

FSU-41, "Wheel Alignment"

.

• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to 

BRC-8,

"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"

.

• Check wheel sensor harness for proper connection. Refer to 

BRC-100, "Removal and Installation"

.

1.

Gasket

2.

Shock absorber mounting bracket

3.

Bound bumper

4.

Rubber seat

5.

Coil spring

6.

Shock absorber 

7.

Stopper rubber

8.

Upper link

9.

Steering knuckle

10. Cotter pin

11. Insulator

12. Transverse link

13. Stabilizer bar

14. Stabilizer connecting rod

15. Stabilizer bushing

16. Stabilizer clamp

17. Front cross bar

18. Front suspension member

Refer to 

GI-4, "Components"

 for symbols in the figure.