Infiniti G35 (V35) Sedan. Manual - part 574

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  572  573  574  575   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 574

 

 

EC-442

< COMPONENT DIAGNOSIS >

[VQ35HR]

P2A00, P2A03 A/F SENSOR 1

• Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread

Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.

Do you have CONSULT-III?

YES

>> GO TO 12.

NO

>> GO TO 13.

12.

CONFIRM A/F ADJUSTMENT DATA

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “A/F ADJ-B1” and “A/F ADJ-B2” in “DATA MONITOR” mode with CONSULT-III.

3.

Make sure that “0.000” is displayed on CONSULT-III screen.

Is “0.000” displayed?

YES

>> INSPECTION END

NO

>> GO TO 13.

13.

CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE

Clear the mixture ratio self-learning value. Refer to 

EC-21, "MIXTURE RATIO SELF-LEARNING VALUE

CLEAR : Special Repair Requirement"

.

Do you have CONSULT-III?

YES

>> GO TO 14.

NO

>> INSPECTION END

14.

CONFIRM A/F ADJUSTMENT DATA

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “A/F ADJ-B1” and “A/F ADJ-B2” in “DATA MONITOR” mode with CONSULT-III.

3.

Make sure that “0.000” is displayed on CONSULT-III screen.

>> INSPECTION END

ASCD BRAKE SWITCH

EC-443

< COMPONENT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

ASCD BRAKE SWITCH

Description

INFOID:0000000000956848

When the brake pedal is depressed, ASCD brake switch is turned OFF and stop lamp switch is turned ON.
ECM detects the state of the brake pedal by this input of two kinds (ON/OFF signal).
Refer to 

EC-57, "System Description"

 for the ASCD function.

Component Function Check

INFOID:0000000000956849

1.

CHECK ASCD BRAKE SWITCH FUNCTION

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.

3.

Check “BRAKE SW1” indication under the following conditions.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-443, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000956850

1.

INSPECTION START

Check which type of transmission the vehicle is equipped with.

Which type of transmission?

A/T

>> GO TO 2.

M/T

>> GO TO 7.

2.

CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ASCD brake switch harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between ASCD brake switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

DETECT MALFUNCTIONING PART

Check the following.

Monitor item

Condition

Indication

BRAKE SW1

Brake pedal (A/T)
Brake pedal and clutch pedal (M/T)

Slightly depressed

OFF

Fully released

ON

ECM

Ground

Condition

Voltage

Connector

Terminal

M107

126

(ASCD brake switch signal)

Ground

Brake pedal (A/T)
Brake pedal and clutch pedal (M/T)

Slightly depressed

Approx. 0V

Fully released

Battery voltage

ASCD brake switch

Ground

Voltage

Connector

Terminal

E109

1

Ground

Battery voltage

EC-444

< COMPONENT DIAGNOSIS >

[VQ35HR]

ASCD BRAKE SWITCH

• Fuse block (J/B) connector E103
• 10A fuse (No. 3)
• Harness for open or short between ASCD brake switch and fuse

>> Repair open circuit or short to ground in harness or connectors.

4.

CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between ASCD brake switch harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E106, M6
• Harness for open or short between ECM and ASCD brake switch

>> Repair open circuit or short to ground or short to power in harness or connectors.

6.

CHECK ASCD BRAKE SWITCH

Refer to 

EC-446, "Component Inspection (ASCD Brake Switch)"

 

Is the inspection result normal?

YES

>> GO TO 15.

NO

>> Replace ASCD brake switch.

7.

CHECK ASCD BRAKE SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ASCD clutch switch harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between ASCD clutch switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> GO TO 8.

8.

CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ASCD brake switch harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between ASCD brake switch harness connector and ground.

ASCD brake switch

ECM

Continuity

Connector

Terminal

Connector

Terminal

E109

2

M107

126

Existed

ASCD clutch switch

Ground

Condition

Voltage

Connector

Terminal

E108

2

Ground

Brake pedal

Slightly depressed

Approx. 0V

Fully released

Battery voltage

ASCD BRAKE SWITCH

EC-445

< COMPONENT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> GO TO 9.

9.

DETECT MALFUNCTIONING PART

Check the following.
• Fuse block (J/B) connector E103
• 10A fuse (No. 3)
• Harness for open or short between ASCD brake switch and fuse

>> Repair open circuit or short to ground in harness or connectors.

10.

CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Check the continuity between ASCD brake switch harness connector and ASCD clutch switch harness
connector.

3.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

11.

CHECK ASCD BRAKE SWITCH

Refer to 

EC-446, "Component Inspection (ASCD Brake Switch)"

.

Is the inspection result normal?

YES

>> GO TO 15.

NO

>> Replace ASCD brake switch.

12.

CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between ASCD clutch switch harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> GO TO 13.

13.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E106, M6
• Harness for open or short between ECM and ASCD clutch switch

>> Repair open circuit or short to ground or short to power in harness or connectors.

ASCD brake switch

Ground

Voltage

Connector

Terminal

E109

1

Ground

Battery voltage

ASCD brake switch

ASCD clutch switch

Continuity

Connector

Terminal

Connector

Terminal

E109

2

E108

2

Existed

ASCD clutch switch

ECM

Continuity

Connector

Terminal

Connector

Terminal

E108

1

M107

126

Existed

 

 

 

 

 

 

 

Content   ..  572  573  574  575   ..