Infiniti G35 (V35) Sedan. Manual - part 419

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  417  418  419  420   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 419

 

 

DLN-110

< PREPARATION >

[FRONT FINAL DRIVE: F160A]

PREPARATION

Commercial Service Tools

INFOID:0000000000957344

ST30031000
(J-22912-01)
Replacer

Removing pinion rear bearing inner race

ST37820000
(

)

Drift
a: 39 mm (1.54 in) dia.
b: 72 mm (2.83 in) dia.

Installing pinion front and rear bearing outer 
race

KV38102510
(

)

Drift
a: 71 mm (2.80 in) dia.
b: 65 mm (2.56 in) dia.

Installing front oil seal

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA0700D

ZZA0836D

ZZA0838D

Tool name

Description

Flange wrench

Removing and installing drive pinion lock nut

Spacer
a: 60 mm (2.36 in) dia.
b: 36 mm (1.42 in) dia.
c: 30 mm (1.18 in)

Installing pinion front bearing inner race

Power tool

Loosening bolts and nuts

NT035

ZZA1133D

PBIC0190E

FRONT FINAL DRIVE ASSEMBLY

DLN-111

< FUNCTION DIAGNOSIS >

[FRONT FINAL DRIVE: F160A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

FUNCTION DIAGNOSIS

FRONT FINAL DRIVE ASSEMBLY

System Diagram

INFOID:0000000000957345

CROSS-SECTION VIEW

1.

Side retainer

2.

Side bearing

3.

Differential case

4.

Drive gear

5.

Pinion mate shaft

6.

Pinion mate gear

7.

Side gear

8.

Side shaft

9.

Gear carrier

10. Drive pinion

11.

Companion flange

12. Pinion front bearing

13. Pinion rear bearing

14. Extension tube retainer

15. Engine assembly

PDIA0647E

DLN-112

< ON-VEHICLE MAINTENANCE >

[FRONT FINAL DRIVE: F160A]

FRONT DIFFERENTIAL GEAR OIL

ON-VEHICLE MAINTENANCE

FRONT DIFFERENTIAL GEAR OIL

Inspection

INFOID:0000000000957346

OIL LEAKAGE

Make sure that oil is not leaking from final drive assembly or around it.

OIL LEVEL

• Remove filler plug (1) and check oil level from filler plug mounting

hole as shown in the figure.

CAUTION:

Never start engine while checking oil level.

• Set a gasket on filler plug (1) and install it on final drive assembly.

Refer to 

DLN-119, "Exploded View"

.

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000000957347

1.

Stop engine.

2.

Remove drain plug (1) and drain gear oil.

3.

Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to 

DLN-119,

"Exploded View"

.

CAUTION:

Never reuse gasket.

Refilling

INFOID:0000000000957348

1.

Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.

2.

After refilling oil, check oil level. Set a gasket to filler plug (1),
then install it to final drive assembly. Refer to 

DLN-119,

"Exploded View"

.

CAUTION:

Never reuse gasket.

PDIA0782J

PDIA0781J

Oil grade and Viscosity

: Refer to 

MA-10, "Fluids 

and Lubricants"

.

Oil capacity

: Refer to 

DLN-144, "Gen-

eral Specifications"

.

PDIA0782J

SIDE OIL SEAL

DLN-113

< ON-VEHICLE REPAIR >

[FRONT FINAL DRIVE: F160A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

ON-VEHICLE REPAIR

SIDE OIL SEAL

RIGHT SIDE

RIGHT SIDE : Exploded View

INFOID:0000000000957349

1.

Drive pinion lock nut

2.

Companion flange

3.

Front oil seal 

4.

Pinion front bearing

5.

Drive pinion bearing adjusting wash-
er

6.

Drive pinion adjusting washer

7.

Gear carrier

8.

Pinion rear bearing

9.

Pinion height adjusting washer 

10. Drive pinion

11.

Drive gear

12. Side oil seal (right side)

13. Side retainer

14. O-ring

15. Side bearing adjusting shim

16. Side bearing

17. Differential case

18. Breather connector 

19. Dowel pin

20. Filler plug

21. Drain plug

22. Gasket

23. Carrier cover

24. Gear oil defense

25. Side gear thrust washer

26. Side gear

27. Circular clip

JSDIA0020GB

 

 

 

 

 

 

 

Content   ..  417  418  419  420   ..