Infiniti G35 (V35) Sedan. Manual - part 407

DLN-62

< DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13B]

FRONT CASE AND REAR CASE

19. Remove mainshaft assembly from rear case, using the drift

[SST: ST33052000 (

—

)].

20. Remove snap ring from rear case.

21. Remove rear bearing from rear case, using the drifts.

22. Remove baffle plate from rear case.

23. Remove breather tube from rear case.

Assembly

INFOID:0000000000957293

PDIA0262E

PDIA0263E

A: Drift bar [ST30611000 (J-25742-1)]

B: Drift [ST35321000 (

—

)]

PDIA0264E

SDIA1701E

FRONT CASE AND REAR CASE

DLN-63

< DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

1.

Install breather tube, with plastic hammer.

CAUTION:

Pay attention to the direction of breather tube.

2.

Install baffle plate to rear case.

3.

Install rear bearing to rear case, using the drift [SST:
KV38104010 (

—

)].

CAUTION:

Apply ATF to inside of rear bearing.

4.

Install snap ring to rear case.

CAUTION:

Never reuse snap ring.

5.

Install mainshaft assembly to rear case, using the drift [SST:
ST35321000 (

—

)].

CAUTION:

ATF should be applied to contact surface of mainshaft and
rear bearing.

6.

Install O-ring to AWD solenoid harness connector.

CAUTION:

• Never reuse O-ring.
• Apply ATF to O-ring.

7.

Install AWD solenoid harness connector into rear case.

8.

Install retainer (1) to AWD solenoid harness connector.

PDIA0274E

PDIA0275E

PDIA0263E

SDIA2368E

JSDIA0100ZZ

DLN-64

< DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13B]

FRONT CASE AND REAR CASE

9.

Set temperature sensor and tighten bolt.

10. Hold electric controlled coupling harness with oil cover hold

plate, install oil cover to rear case.

CAUTION:

The harness should be guided by a cut portion.

11. Install oil gutter (1) to rear case.

CAUTION:

The tip of oil gutter should be put into rear case groove.

12. Install drive chain to front drive shaft.

CAUTION:

Identification mark of drive chain should be in the side of
front bearing of front drive shaft.

13. Install drive chain to mainshaft, and then install tap front drive

shaft with plastic hammer. Press-fit rear bearing of front drive
shaft to rear case.

CAUTION:

Never tap drive chain.

SDIA2404E

JSDIA0098ZZ

PDIA0284E

PDIA0257E

FRONT CASE AND REAR CASE

DLN-65

< DISASSEMBLY AND ASSEMBLY >

[TRANSFER: ETX13B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

14. Install mainshaft bearing to front case, using the drift [SST:

ST30621000 (J-25742-5)].

15. Install snap ring to front case.

CAUTION:

Never reuse snap ring.

16. Apply liquid gasket to mating surface of rear case. 

• Use Genuine Anaerobic Liquid Gasket or equivalent.

Refer to 

GI-15, "Recommended Chemical Products and

Sealants"

.

CAUTION:

Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.

17. Set front case to rear case.

CAUTION:

Never damage the mating surface transmission side.

PDIA0283E

PDIA0267E

PDIA0532J

PDIA0279E