Infiniti G35 (V35) Sedan. Manual - part 1358

TM-124

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0705 PARK/NEUTRAL POSITION SWITCH

P0705 PARK/NEUTRAL POSITION SWITCH

Description

INFOID:0000000000957020

• The park/neutral position (PNP) switch includes the transmission range switch.
• The transmission range switch detects the selector lever position and transmits a signal to the TCM.

DTC Logic

INFOID:0000000000957021

DTC DETECTION LOGIC

*: This is an OBD-II self-diagnostic item.

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

  With CONSULT-III

1.

Start the engine.

2.

Select “DATA MONITOR”.

3.

Drive vehicle and maintain the following conditions for least 2 consecutive seconds.

  With GST

Follow the procedure “With CONSULT-III”.

Is “P0705 PNP SW/CIRC” detected?

YES

>> Go to 

TM-124, "Diagnosis Procedure"

.

NO

>> Check Intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000000957022

1.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-168, "Diagnosis Procedure"

.

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK PARK/NEUTRAL POSITION SWITCH HARNESS CONNECTOR AND TCM HARNESS CONNEC-

TOR

1.

Remove control valve with TCM. Refer to 

TM-240, "Exploded View"

.

2.

Disconnect park/neutral position switch connector and TCM connector.

3.

Check continuity between park/neutral position switch connector and TCM connector.

DTC

Item

(CONSULT-III screen 

terms)

A/T CHECK indicator 
lamp judgment flicker

Diagnostic item is de-

tected when...

Possible cause

P0705*

PNP SW/CIRC

9th

• PNP switch 1 – 4 sig-

nals input with impos-
sible pattern.

• P position is detected 

from N position with-
out any other position 
being detected in be-
tween.

• Harness or connectors

[Park/neutral position 
(PNP) switches 1, 2, 3, 
4 and TCM circuit is 
open or shorted.]

• Park/neutral position 

(PNP) switches 1, 2, 3 
and 4

ACCELE POSI

: More than 1.0/8

P0705 PARK/NEUTRAL POSITION SWITCH

TM-125

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

4.

If OK, check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> Replace the control valve with TCM. Refer to 

TM-240, "Exploded View"

.

NO

>> Replace open circuit or short to ground and short to power in harness or connectors.

Park/neutral position switch connector

TCM connector

Continuity

Connector

Terminal

Connector

Terminal

F154

1

F152

13

Existed

2

11

Existed

3

12

Existed

5

14

Existed

TM-126

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0717 TURBINE REVOLUTION SENSOR

P0717 TURBINE REVOLUTION SENSOR

Description

INFOID:0000000000957023

The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the A/T. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.

DTC Logic

INFOID:0000000000957024

DTC DETECTION LOGIC

*: This is an OBD-II self-diagnostic item.

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

  With CONSULT-III

1.

Start the engine.

2.

Select “DATA MONITOR”.

3.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

  With GST

Follow the procedure “With CONSULT-III”.
Is “P0717 TURBINE REV S/CIRC” detected?

YES

>> Go to 

TM-126, "Diagnosis Procedure"

.

NO

>> Check Intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000000957025

1.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-168, "Diagnosis Procedure"

.

Is the inspection result normal?

DTC

Item

(CONSULT-III screen 

terms)

A/T CHECK indicator 
lamp judgment flicker

Diagnostic item is de-

tected when...

Possible cause

P0717*

TURBINE REV S/CIRC

11th

• TCM does not receive 

the proper voltage sig-
nal from the sensor.

• TCM detects an irreg-

ularity only at position 
of 4th gear for turbine 
revolution sensor 2.

• Harness or connectors

(Sensor circuit is open 
or shorted.)

• Turbine revolution 

sensor 1 and/or 2

VHCL/S SE-A/T

: 40 km/h (25 MPH) or more

ACCELE POSI

: More than 0.5/8

ENGINE SPEED

: 1,500 rpm or more

SLCT LVR POSI

: “D” position

GEAR (Turbine revo-
lution sensor 1)

: “4” or “5” position

GEAR (Turbine revo-
lution sensor 2)

: All positions

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the driving con-
ditions required for this test.

P0717 TURBINE REVOLUTION SENSOR

TM-127

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

YES

>> Replace the control valve with TCM. Refer to 

TM-240, "Exploded View"

.

NO

>> Repair or replace damaged parts.