Infiniti G35 (V35) Sedan. Manual - part 55

ADP-214

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000000960771

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Service

INFOID:0000000000960772

• When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent

scratches.

• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or

damage them.

• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-

tion measures.

Work

INFOID:0000000000960773

• When removing or disassembling each component, be careful not to damage or deform it. If a component

may be subject to interference, be sure to protect it with a shop cloth.

• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component

with a shop cloth or vinyl tape to protect it.

• Protect the removed parts with a shop cloth and keep them.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After re-installation is completed, be sure to check that each part works normally.
• Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the

fouled area.
Then rub with a soft and dry cloth.

- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe

the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.

• Do not use organic solvent such as thinner, benzene, alcohol, and gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.

PRE-INSPECTION FOR DIAGNOSTIC

ADP-215

< ON-VEHICLE MAINTENANCE >

ADP

ON-VEHICLE MAINTENANCE

PRE-INSPECTION FOR DIAGNOSTIC

Basic Inspection

INFOID:0000000000960774

CHECK POWER SUPPLY AND DROUND CIRCUIT

Check the power supply and ground circuit as shown below.
• Driver seat control unit :Refer to

ADP-66, "DRIVER SEAT CONTROL UNIT : Diagnosis Procedure"

• Automatic drive positioner control unit: Refer to

ADP-67, "AUTOMATIC DRIVE POSITIONER CONTROL

UNIT : Diagnosis Procedure"

Is the inspection result normally?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning part.

CHECK MANUAL FUNCTION

Check the manual function operations by operating the relevant switches as shown below.
• Seat (slide, reclining, lifting front, lifting rear)
• Steering column (tilt, telescopic)
• Door mirror
• Side support

Do all manual functions operate normally?

YES

>> GO TO 3.

NO (Seat, steering, door mirror)>>Go to SYMPTOM 1, refer to

ADP-211, "Symptom Table"

. And, GO TO 4 if

the result of SYMPTOM 1 is OK.

NO (Side support)>>Go to SYMPTOM 7, refer to

ADP-211, "Symptom Table"

CHECK MEMORY FUNCTION 1

ADP-10, "MEMORY STORING : Description"

) and check that all parts of