Infiniti G20 (P11). Manual - part 177

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  175  176  177  178   ..

 

 

Infiniti G20 (P11). Manual - part 177

 

 

21

CHECK IGNITION TIMING-I

Without CONSULT-II

1. Turn ignition switch “OFF”.
2. Release vacuum from throttle opener.
3. Remove vacuum pump and vacuum hose from throttle opener.
4. Reinstall original vacuum hose to throttle opener securely.
5. Start engine and warm it up to normal operating temperature.
6. Stop engine and disconnect throttle position sensor harness connector.

SEF863X

7. Start engine.
8. Check ignition timing at idle using a timing light.

SEF284G

Ignition timing:

M/T 15°

±

2° BTDC

A/T 15°

±

2° BTDC (in “P” or “N” position)

OK or NG

OK

©

GO TO 22.

NG

©

1. Adjust ignition timing by turning distributor. Refer to “Idle Speed/Ignition Timing/Idle

Mixture Ratio Adjustment”, EC-53.

2. GO TO 22.

GI

MA

EM

LC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX

TROUBLE DIAGNOSIS — BASIC INSPECTION

Basic Inspection (Cont’d)

EC-119

22

CHECK IGNITION TIMING-II

1. Stop engine.
2. Reconnect throttle position sensor harness connector.
3. Start engine and let it idle.
4. Check ignition timing at idle using a timing light.

SEF984U

Ignition timing:

M/T 15°

±

2° BTDC

A/T 15°

±

2° BTDC (in “P” or “N” position)

OK or NG

OK

©

GO TO 33.

NG

©

GO TO 23.

23

PERFORM IDLE AIR VOLUME LEARNING

Refer to “Idle Air Volume Learning”, EC-65.
Is the result CMPLT or INCMP?

CMPLT or INCMP

CMPLT

©

GO TO 24.

INCMP

©

Follow the construction of “Idle Air Volume Learning”.

24

CHECK IGNITION TIMING AGAIN

Check ignition timing again. Refer to Test No. 16 (With CONSULT-II) or 22 (Without CONSULT-II).

OK or NG

OK (With CONSULT-II)

©

GO TO 30.

OK (Without CONSULT-
II)

©

GO TO 33.

NG

©

GO TO 25.

25

CHECK FOR INTAKE AIR LEAK

1. Start engine and let it idle.
2. Listen for an air leak from PCV hose and after IACV-AAC valve.

OK or NG

OK

©

GO TO 27.

NG

©

GO TO 26.

26

REPAIR MALFUNCTION

1. Stop engine.
2. Repair or replace malfunctioning part.

©

GO TO 23.

TROUBLE DIAGNOSIS — BASIC INSPECTION

Basic Inspection (Cont’d)

EC-120

27

DETECT MALFUNCTIONING PART

Check the IACV-AAC valve circuit and function. Refer to EC-436.

OK or NG

OK

©

GO TO 29.

NG

©

GO TO 28.

28

REPAIR MALFUNCTION

Repair or replace malfunction part following the “Diagnostic Procedure” corresponding the detected malfunction.

©

GO TO 23.

29

CHECK ECM FUNCTION

1. Substitute another known-good ECM to check ECM function.

(ECM may be the cause of a problem, but this is rarely the case.)

2. Perform initialization of IVIS (NATS) system and registration of IVIS (NATS) ignition key IDs. Refer to “IVIS (INFINITI

Vehicle Immobilizer System — NATS)”, EC-81.

©

GO TO 23.

30

CHECK TARGET IDLE SPEED

With CONSULT-II

1. Start engine and warm it up to normal operating temperature.
2. Select “ENG SPEED” in “DATA MONITOR” mode.
3. Check idle speed.

M/T: 800

±

50 rpm

A/T: 800

±

50 rpm (in “P” or “N” position)

OK or NG

OK

©

GO TO 36.

NG

©

GO TO 31.

31

PERFORM IDLE AIR VOLUME LEARNING

Refer to “Idle Air Volume Learning”, EC-65.
Is the result CMPLT or INCMP?

CMPLT or INCMP

CMPLT

©

GO TO 32.

INCMP

©

Follow the construction of “Idle Air Volume Learning”.

32

CHECK TARGET IDLE SPEED AGAIN

1. Start engine and warm it up to normal operating temperature.
2. Select “ENG SPEED” in “DATA MONITOR” mode with CONSULT-II.
3. Check idle speed.

M/T: 800

±

50 rpm

A/T: 800

±

50 rpm (in “P” or “N” position)

OK or NG

OK

©

GO TO 36.

NG

©

GO TO 25.

GI

MA

EM

LC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX

TROUBLE DIAGNOSIS — BASIC INSPECTION

Basic Inspection (Cont’d)

EC-121

33

CHECK TARGET IDLE SPEED

Without CONSULT-II

1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.

M/T: 800

±

50 rpm

A/T: 800

±

50 rpm (in “P” or “N” position)

OK or NG

OK

©

GO TO 36.

NG

©

GO TO 34.

34

PERFORM IDLE AIR VOLUME LEARNING

Refer to “Idle Air Volume Learning”, EC-65.
Is the result CMPLT or INCMP?

CMPLT or INCMP

CMPLT

©

GO TO 35.

INCMP

©

Follow the construction of “Idle Air Volume Learning”.

35

CHECK TARGET IDLE SPEED AGAIN

1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.

M/T: 800

±

50 rpm

A/T: 800

±

50 rpm (in “P” or “N” position)

OK or NG

OK

©

GO TO 36.

NG

©

GO TO 25.

36

ERASE UNNECESSARY DTC

After this inspection, unnecessary DTC No. might be displayed.
Erase the stored memory in ECM and TCM (Transmission control module).
Refer to “HOW TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION”, EC-79 and “HOW TO ERASE DTC”,
AT-38.

©

INSPECTION END

TROUBLE DIAGNOSIS — BASIC INSPECTION

Basic Inspection (Cont’d)

EC-122

 

 

 

 

 

 

 

Content   ..  175  176  177  178   ..