Infiniti G20 (P11). Manual - part 112

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  110  111  112  113   ..

 

 

Infiniti G20 (P11). Manual - part 112

 

 

SBR574

Assembly

NCBR0034

1.

Insert piston seal into groove on cylinder body.

2.

With piston boot fitted to piston, insert piston boot into groove
on cylinder body and install piston.

3.

Properly secure piston boot.

SBR980B

Installation

NCBR0035

CAUTION:

I

Refill with new brake fluid “DOT 3”.

I

Never reuse drained brake fluid.

1.

Install brake hose to caliper securely.

2.

Install all parts and secure all bolts.

3.

Bleed air. Refer to “Bleeding Brake System”, BR-8.

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

ST

RS

BT

HA

SC

EL

IDX

FRONT DISC BRAKE

Assembly

BR-23

Component

NCBR0038

SBR895D

1.

Cable guide

2.

Cylinder

3.

Toggle lever

4.

Pin

5.

Pin boot

6.

Torque member

7.

Inner shim

8.

Inner pad

9.

Pad retainer

10. Outer pad

11. Outer shim
12. Strut
13. O-ring
14. Push rod
15. Key plate
16. Snap ring C
17. Seat
18. Spring
19. Spring cover
20. Snap ring B

21. Piston seal
22. Snap ring A
23. Spacer
24. Wave washer
25. Spacer
26. Bearing
27. Adjuster
28. Cup
29. Piston
30. Piston boot

Pad Replacement

NCBR0037

WARNING:

Clean brake pads with a vacuum dust collector to minimize the
hazard of airborne particles or other materials.

CAUTION:

I

When cylinder body is open, do not depress brake pedal
because piston will pop out.

I

Be careful not to damage piston boot or get oil on rotor.
Always replace shims in replacing pads.

I

If shims are rusted or show peeling of rubber coat, replace
them with new shims.

REAR DISC BRAKE

Component

BR-24

I

It is not necessary to remove connecting bolt except for
disassembly or replacement of caliper assembly. In this
case, suspend cylinder body with wire so as not to stretch
brake hose.

I

Burnish the brake contact surfaces after refinishing or
replacing drums or rotors, after replacing pads or linings,
or if a soft pedal occurs at very low mileage.
Refer to “Brake Burnishing Procedure”, “ON-VEHICLE
SERVICE”, BR-7.

SBR938C

SBR916C

1.

Remove master cylinder reservoir cap.

2.

Remove brake cable mounting bolt and lock spring.

3.

Release parking brake control lever, then disconnect cable
from the caliper.

4.

Remove upper pin bolt.

5.

Open cylinder body downward. Then remove pad retainers,
and inner and outer shims.

Standard pad thickness:

10 mm (0.39 in)

Pad wear limit:

1.5 mm (0.059 in)

SBR641

SBR868C

6.

When installing new pads, push piston into cylinder body by
gently turning piston clockwise, as shown.
Carefully monitor brake fluid level because brake fluid will
return to reservoir when pushing back piston.

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

ST

RS

BT

HA

SC

EL

IDX

REAR DISC BRAKE

Pad Replacement (Cont’d)

BR-25

SBR306E

7.

Adjust the piston to the right angle as shown in the figure.

SBR307E

8.

As shown in the figure, align the piston’s concave to the pad’s
convex, then install the cylinder body to the torque member.

SBR939C

Removal

NCBR0039

WARNING:

Clean brake pads with a vacuum dust collector to minimize the
hazard of airborne particles or other materials.
1.

Remove brake cable mounting bolt and lock spring.

2.

Release parking brake control lever, then disconnect cable
from the caliper.

3.

Remove torque member fixing bolts and connecting bolt.

It is not necessary to remove connecting bolt except for dis-
assembly or replacement of caliper assembly. In this case,
suspend caliper assembly with wire so as not to stretch brake
hose.

REAR DISC BRAKE

Pad Replacement (Cont’d)

BR-26

 

 

 

 

 

 

 

Content   ..  110  111  112  113   ..