Infiniti FX35 / FX45. Manual - part 949

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  947  948  949  950   ..

 

 

Infiniti FX35 / FX45. Manual - part 949

 

 

PREPARATION

TF-7

< SERVICE INFORMATION >

C

E

F

G

H

I

J

K

L

M

A

B

TF

N

O

P

Commercial Service Tool

INFOID:0000000001327427

ST30611000
(J-25742-1)
Drift bar
a: 350 mm (1.10 in)
b: 25 mm (1.10 in) dia.
c: M12 

×

 1.5P

• Removing rear bearing

ST35321000
(

)

Drift
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.

• Removing rear bearing
• Installing mainshaft assembly

ST31214000
(J-25269-B)
Drift
a: 34 mm (1.34 in) dia.
b: 25.5 mm (1.004 in) dia.

• Removing front drive shaft front bearing
• Removing front drive shaft rear bearing

KV38104010
(

)

Drift
a: 67 mm (2.64 in) dia.
b: 49 mm (1.93 in) dia.

• Installing front drive shaft rear bearing
• Installing rear bearing

ST33200000
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.

• Installing front drive shaft front bearing

ST30621000
(J-25742-5)
Drift
a: 80 mm (3.15 in) dia.
b: 59 mm (2.32 in) dia.

• Installing mainshaft bearing

Tool number
(Kent-Moore No.)
Tool name

Description

NT663

ZZA1000D

ZZA0534D

ZZA1000D

ZZA1002D

ZZA1000D

TF-8

< SERVICE INFORMATION >

PREPARATION

Tool name

Description

Puller

• Removing companion flange

Flange wrench

• Removing and installing self-lock nut

Puller

• Removing front drive shaft front bearing
• Removing front drive shaft rear bearing

Power tool

• Loosening bolts and nuts

NT077

NT771

ZZB0823D

PBIC0190E

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

TF-9

< SERVICE INFORMATION >

C

E

F

G

H

I

J

K

L

M

A

B

TF

N

O

P

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000001327428

Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.

Reference page

TF-1

0

TF-4

0

TF-4

0

TF-4

0

TF-4

0

TF-4

0

SUSPECTED PARTS
(Possible cause)

TRANSFE

R

 FLUID (Level low)

TRANSFE

R

 FLUI

(W

rong)

T

R

ANSF

ER

 F

L

UID (L

ev

el

 to

o h

ig

h

)

LI

QUI

D

 GA

SKET (D

amaged)

OIL SEAL 

(W

orn or 

damaged)

GEAR (W

orn

 or 

da

ma

ge

d)

BEARING (W

orn or damaged)

TRANSFE

R

 CASE 

(Damaged)

Symptom

Noise

1

2

3

3

3

Transfer fluid leakage

4

1

2

2

3

TF-10

< SERVICE INFORMATION >

TRANSFER FLUID

TRANSFER FLUID

Replacement

INFOID:0000000001327429

DRAINING

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine, and remove the drain plug to drain the transfer
fluid.

3.

Apply sealant to drain plug. Install drain plug on transfer and
tighten to the specified torque. Refer to 

TF-40, "Disassembly

and Assembly"

.

• Use Genuine Silicone RTV or equivalent. Refer to 

GI-44,

"Recommended Chemical Product and Sealant"

.

FILLING

1.

Remove filler plug and add transfer fluid until fluid level reaches
the specified limit near filler plug mounting hole.

CAUTION:

Carefully fill the fluid. (Fill up for approx. 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the fluid level again.

3.

Set a new gasket onto filler plug and install it on transfer and tighten to the specified torque. Refer to 

TF-

40, "Disassembly and Assembly"

.

CAUTION:

Do not reuse gasket.

Inspection

INFOID:0000000001327430

FLUID LEAKAGE AND FLUID LEVEL

1.

Check fluid level from filler plug mounting hole as shown in the
figure.

2.

Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to 

TF-40, "Dis-

assembly and Assembly"

.

CAUTION:

Do not reuse gasket.

SDIA2087E

Fluid and viscosity

: Refer to 

MA-9, "Fluids and Lubricants"

.

Fluid capacity

: Approx. 1.25  (2-5/8 US pt, 2-1/4 lmp pt)

SDIA2028E

SDIA2028E

 

 

 

 

 

 

 

Content   ..  947  948  949  950   ..