Infiniti FX35 / FX45. Manual - part 900

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  898  899  900  901   ..

 

 

Infiniti FX35 / FX45. Manual - part 900

 

 

RSU-16

< SERVICE INFORMATION >

STABILIZER BAR

STABILIZER BAR

Removal and Installation

INFOID:0000000001327561

REMOVAL

1.

Remove tires from vehicle with power tool.

2.

Remove center muffler from vehicle. Refer to 

EX-3, "Component"

.

3.

Remove fixing bolts and remove stabilizer connecting rod mount bracket from suspension arm with power
tool.

4.

Remove lower side fixing nut on stabilizer connecting rod and remove stabilizer connecting rod from stabi-
lizer bar with power tool.

5.

Remove fixing nuts on stabilizer clamps and remove stabilizer from vehicle with power tool.

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer bushings, stabilizer clamps, stabilizer connecting rod, stabilizer connecting rod
mounting bracket for any deformation, cracks or damage. Replace if necessary.

INSTALLATION

• Refer to 

RSU-6, "Removal and Installation"

 for tightening torque. Install in the reverse order of removal.

NOTE:
Refer to component parts location and do not reuse non-reusable parts.

• Stabilizer bar uses pillow ball type connecting rod, position ball

joint with case on pillow ball head parallel to stabilizer bar.

• When the bushing and clamp are installed to stabilizer bar, position

the bushing and clamp inside of the side slip prevention clamp.

SFA449BB

REAR SUSPENSION MEMBER

RSU-17

< SERVICE INFORMATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

REAR SUSPENSION MEMBER

Removal and Installation

INFOID:0000000001327562

REMOVAL

1.

Remove tires from vehicle with power tool.

2.

Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to

BR-

24

.

NOTE:
Avoid depressing brake pedal while brake caliper is removed.

3.

Remove wheel sensor from rear final drive, then remove wheel sensor harness from rear suspension
member. Refer to 

BRC-52

.

4.

Remove height sensor harness from rear suspension member (if equipped).

5.

Remove center muffler and main muffler. Refer to 

EX-3

.

6.

Remove stabilizer bar. Refer to 

RSU-16, "Removal and Installation"

.

7.

Remove rear drive shaft. Refer to 

RAX-10

.

8.

Remove propeller shaft. Refer to 

PR-7

.

9.

Remove rear final drive. Refer to 

RFD-16, "Removal and Installation"

.

10. Separate attachments between parking brake cable and vehicle and rear suspension member. Refer to

PB-4

.

11. Remove rear lower link and coil spring. Refer to 

RSU-14, "Removal and Installation"

.

12. Remove fixing bolt in lower side of shock absorber with power tool.

13. Set jack under rear suspension member.

14. Remove fixing bolts and nuts of tunnel stay and member stay with power tool, then remove those parts

from vehicle and rear suspension member.

15. Remove fixing bolts and nuts of rear pin stay with power tool and then remove rear pin stay from vehicle

and rear suspension member. 

16. Slowly lowering jack, then remove rear suspension member, suspension arm, radius rod, front lower link

and axle from vehicle as a unit.

17. Remove fixing bolts and nuts with power tool, then remove suspension arm, front lower link, and radius

rod from rear suspension member.

INSPECTION AFTER REMOVAL

Check rear suspension member for deformation, cracks, and other damage and replace if necessary.

INSTALLATION

• Refer to 

RSU-6, "Removal and Installation"

, for tightening torque. Install in the reverse order of removal.

NOTE:
Refer to component parts location and do not reuse non-reusable parts.

• Perform final tightening of installation position of links (rubber bushing) under unladen conditions with tires

on level ground. Check wheel alignment. Refer to 

RSU-5, "Wheel AlignmentInspection"

.

• After adjusting wheel alignment, adjust neutral position of steering angle sensor. Refer to 

BRC-8, "Adjust-

ment of Steering Angle Sensor Neutral Position"

.

RSU-18

< SERVICE INFORMATION >

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Alignment (Unladen*)

INFOID:0000000001327563

*: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

INFOID:0000000001327564

Wheelarch Height (Unladen*)

INFOID:0000000001327565

*: Fuel, engine coolant and lubricant are oil full. Spare tire, jack, hand tools and mats are in designated positions.

Camber
Degree minute (Decimal degree)

Minimum

–1

°

18

′

 (–1.30

°

)

Nominal

–0

°

48

′

 (–0.80

°

)

Maximum

–0

°

18

′

 (–0.30

°

)

Total toe-in

Distance 

Minimum

2.4 mm (0.09 in)

Nominal

4.7 mm (0.19 in)

Maximum

7.0 mm (0.28 in)

Angle (left wheel or right wheel)
Degree minute (Decimal degree)

Minimum

0

°

05

′

 (0.08

°

)

Nominal

0

°

10

′

 (0.17

°

)

Maximum

0

°

15

′

 (0.25

°

)

Axial end play

0 mm (0 in)

Swing torque

0.5 

−

 3.4 N·m (0.06 

−

 0.34 kg-m, 5 

−

 30 in-lb)

Measurement on spring balance (cotter pinhole position)

9.7 

−

 66.0 N (0.98 

−

 6.7 kg, 2.18 

−

 14.8 lb)

Rotating torque

0.5 

−

 3.4 N·m (0.06 

−

 0.34 kg-m, 5 

−

 30 in-lb)

Destination

USA

Canada

Engine

VQ35DE

VK45DE

VQ35DE

VK45DE

Axle

2WD

AWD

AWD

Tire size

265/60R18

265/50R20

265/60R18

265/50R20

265/60R18

265/50R20

Front (Hf)

835 mm

(32.87 in)

834 mm

(32.83 in)

834 mm

(32.83 in)

833 mm

(32.80 in)

832 mm

(32.76 in)

834 mm

(32.83 in)

833 mm

(32.80 in)

832 mm

(32.76 in)

Rear (Hr)

822 mm

(32.36 in)

821 mm

(32.32 in)

829 mm

(32.64 in)

827 mm

(32.56 in)

825 mm

(32.48 in)

827 mm

(32.56 in)

826 mm

(32.52 in)

823 mm

(32.40 in)

SFA818A

 

 

 

 

 

 

 

Content   ..  898  899  900  901   ..