Infiniti FX35 / FX45. Manual - part 725

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  723  724  725  726   ..

 

 

Infiniti FX35 / FX45. Manual - part 725

 

 

CONSULT-III/GST CHECKING SYSTEM

GI-35

< SERVICE INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

GI

N

O

P

CONSULT-III/GST Data Link Connector (DLC) Circuit

INFOID:0000000001572195

INSPECTION PROCEDURE

If the CONSULT-III/GST cannot diagnose the system properly, check the following items.

NOTE:
The DDL1 and DDL2 circuits from DLC pins 12, 13, 14 and 15 may be connected to more than one system. A
short in a DDL circuit connected to a control unit in one system may affect CONSULT-III access to other sys-
tems.
If the GST cannot operate properly, check the circuit based on the information of SAE J1962 and ISO 15031-
3.

Symptom

Check item

CONSULT-III/GST cannot ac-
cess any system.

• CONSULT-III/GST DLC power supply circuit (Terminal 8 and 16) and ground circuit (Terminal 4 and 

5)

CONSULT-III cannot access in-
dividual system. (Other sys-
tems can be accessed.)

• Power supply and ground circuit for the control unit of the system (For detailed circuit, refer to wiring 

diagram for each system.)

• Open or short circuit between the system and CONSULT-III DLC (For detailed circuit, refer to wiring 

diagram for each system.)

• Open or short circuit CAN communication line. Refer to 

LAN-14, "Trouble Diagnosis Flow Chart"

.

GI-36

< SERVICE INFORMATION >

CONSULT-III/GST CHECKING SYSTEM

Wiring Diagram - CONSULT-III/GST CHECKING SYSTEM -

INFOID:0000000001572196

TAWM0074E

LIFTING POINT

GI-37

< SERVICE INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

GI

N

O

P

LIFTING POINT

Commercial Service Tool

INFOID:0000000001325680

CAUTION:

• Every time the vehicle is lifted up,  maintain the complete vehicle curb condition.
• Since the vehicle's center of gravity changes when removing main parts on the front side (engine,

transmission, suspension etc.), support a jack up point on the rear side garage jack with a mission
jack or  equivalent. 

• Since the vehicle's center of gravity changes when removing main parts on the rear side (rear axle,

suspension, etc.), support a jack up point on the front side garage jack with a mission jack or equiv-
alent. 

• Be careful not to smash or do not do anything that would affect piping parts.

Garage Jack and Safety Stand

INFOID:0000000001325681

WARNING:

• Park the vehicle on a level surface when using the jack. Make sure to avoid damaging pipes, tubes,

etc. under the vehicle.

• Never get under the vehicle while it is supported only by the jack. Always use safety stands when

you have to get under the vehicle.

Tool name

Description

Board on attachment

Safety stand attachment

S-NT001

S-NT002

GI-38

< SERVICE INFORMATION >

LIFTING POINT

• Place wheel chocks at both front and back of the wheels on the ground.

CAUTION:

There is canister just behind Garage jack point rear. Jack up be carefully.

2-Pole Lift

INFOID:0000000001325682

WARNING:

When lifting the vehicle, open the lift arms as wide as possible and ensure that the front and rear of the
vehicle are well balanced.
When setting the lift arm, do not allow the arm to contact the brake tubes, brake cable, fuel lines and
sill spoiler.

Board-On Lift

INFOID:0000000001325683

CAUTION:

Make sure vehicle is empty when lifting.

PIIB8452E

PAIA0096E

 

 

 

 

 

 

 

Content   ..  723  724  725  726   ..