Infiniti FX35 / FX45. Manual - part 570

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  568  569  570  571   ..

 

 

Infiniti FX35 / FX45. Manual - part 570

 

 

DTC P1225 TP SENSOR

EC-1041

< SERVICE INFORMATION >

[VK45DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

DTC P1225 TP SENSOR

Component Description

INFOID:0000000001326904

Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has the two sensors. These sensors are
a kind of potentiometers which transform the throttle valve position
into output voltage, and emit the voltage signal to the ECM. In addi-
tion, these sensors detect the opening and closing speed of the
throttle valve and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and the ECM controls the throttle control motor to make the
throttle valve opening angle properly in response to driving condi-
tion.

On Board Diagnosis Logic

INFOID:0000000001326905

The MIL will not light up for this diagnosis.

DTC Confirmation Procedure

INFOID:0000000001326906

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF, wait at least 10 seconds.

3.

Turn ignition switch ON.

4.

Check 1st trip DTC.

5.

If 1st trip DTC is detected, go to 

EC-1041, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000001326907

1.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

1.

Turn ignition switch OFF.

2.

Remove the intake air duct.

3.

Check if foreign matter is caught between the throttle valve (1)
and the housing.

-

Illustration shows the view with intake air duct removed.

OK or NG

OK

>> GO TO 2.

NG

>> Remove the foreign matter and clean the electric throttle

control actuator inside.

2.

REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1.

Replace the electric throttle control actuator.

2.

Perform 

EC-663, "Throttle Valve Closed Position Learning"

.

3.

Perform 

EC-663, "Idle Air Volume Learning"

.

PBIB0145E

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1225
1225

Closed throttle position 
learning performance

Closed throttle position learning value is exces-
sively low.

• Electric throttle control actuator

(TP sensor 1 and 2)

PBIB3247E

EC-1042

< SERVICE INFORMATION >

[VK45DE]

DTC P1225 TP SENSOR

>> INSPECTION END

Removal and Installation

INFOID:0000000001326908

ELECTRIC THROTTLE CONTROL ACTUATOR

Refer to 

EM-175

.

DTC P1226 TP SENSOR

EC-1043

< SERVICE INFORMATION >

[VK45DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

DTC P1226 TP SENSOR

Component Description

INFOID:0000000001326909

Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement. 
The throttle position sensor has the two sensors. These sensors are
a kind of potentiometers which transform the throttle valve position
into output voltage, and emit the voltage signal to the ECM. In addi-
tion, these sensors detect the opening and closing speed of the
throttle valve and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and the ECM controls the throttle control motor to make the
throttle valve opening angle properly in response to driving condi-
tion.

On Board Diagnosis Logic

INFOID:0000000001326910

The MIL will not light up for this diagnosis.

DTC Confirmation Procedure

INFOID:0000000001326911

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF, wait at least 10 seconds.

3.

Turn ignition switch ON.

4.

Repeat steps 2 and34 for 32 times.

5.

Check 1st trip DTC.

6.

If 1st trip DTC is detected, go to 

EC-1043, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000001326912

1.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

1.

Turn ignition switch OFF.

2.

Remove the intake air duct.

3.

Check if foreign matter is caught between the throttle valve (1)
and the housing.

-

Illustration shows the view with intake air duct removed.

OK or NG

OK

>> GO TO 2.

NG

>> Remove the foreign matter and clean the electric throttle

control actuator inside.

2.

REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1.

Replace the electric throttle control actuator.

PBIB0145E

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1226
1226

Closed throttle position 
learning performance

Closed throttle position learning is not per-
formed successfully, repeatedly.

• Electric throttle control actuator

(TP sensor 1 and 2)

PBIB3247E

EC-1044

< SERVICE INFORMATION >

[VK45DE]

DTC P1226 TP SENSOR

2.

Perform 

EC-663, "Throttle Valve Closed Position Learning"

.

3.

Perform 

EC-663, "Idle Air Volume Learning"

.

>> INSPECTION END

Removal and Installation

INFOID:0000000001326913

ELECTRIC THROTTLE CONTROL ACTUATOR

Refer to 

EM-175

.

 

 

 

 

 

 

 

Content   ..  568  569  570  571   ..