Infiniti FX35 / FX45. Manual - part 97

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  95  96  97  98   ..

 

 

Infiniti FX35 / FX45. Manual - part 97

 

 

AT-316

< SERVICE INFORMATION >

ASSEMBLY

iii.

Tighten adapter case assembly mounting bolts (1) to specified
torque. [With bracket (2).] Refer to 

AT-249, "Component"

.

: Bolt (10)

CAUTION:

Do not reuse self-sealing bolts (3).
Refer to GI section to mark sure icons (symbol marks) in the fig-
ure. Refer to 

GI-8, "Component"

.

35. Install needle bearing in drum support.

CAUTION:

• Take care with the direction of needle bearing. Refer to

AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"

.

• Apply petroleum jelly to needle bearing.

36. Install direct clutch assembly in reverse brake.

CAUTION:

Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.

37. Install high and low reverse clutch assembly in direct clutch.

SCIA7210E

SCIA5198E

SCIA5019E

SCIA2306E

ASSEMBLY

AT-317

< SERVICE INFORMATION >

D

E

F

G

H

I

J

K

L

M

A

B

AT

N

O

P

38. Using a flat-bladed screwdriver, align drive plate.

39. Install high and low reverse clutch hub, mid sun gear assembly

and rear sun gear assembly as a unit.

CAUTION:

Check that portion “A” of high and low reverse clutch drum
protrudes approximately 2 mm (0.08 in) beyond portion “B”
of rear sun gear.

40. Install needle bearing in rear carrier assembly.

CAUTION:

• Take care with the direction of needle bearing. Refer to

AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"

.

• Apply petroleum jelly to needle bearing.

SCIA3169E

SCIA5018E

SCIA3130E

SCIA2803E

AT-318

< SERVICE INFORMATION >

ASSEMBLY

41. Install bearing race in rear carrier assembly.

CAUTION:

Apply petroleum jelly to bearing race.

42. Install rear carrier assembly in direct clutch drum.

43. Install needle bearing (rear side) to mid carrier assembly.

CAUTION:

• Take care with the direction of needle bearing. Refer to

AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"

.

• Apply petroleum jelly to needle bearing.

44. Install needle bearing (front side) to mid carrier assembly.

CAUTION:

• Take care with the direction of needle bearing. Refer to

AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"

.

• Apply petroleum jelly to needle bearing.

45. Install mid carrier assembly in rear carrier assembly.

SCIA5175E

SCIA2462E

SCIA2804E

SCIA2805E

SCIA5017E

ASSEMBLY

AT-319

< SERVICE INFORMATION >

D

E

F

G

H

I

J

K

L

M

A

B

AT

N

O

P

46. Install front carrier assembly, input clutch assembly and rear

internal gear as a unit.

47. Install seal rings in input clutch assembly.

CAUTION:

• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.

48. Install band servo anchor end pin and lock nut in transmission

case.

CAUTION:

Do not reuse band servo anchor end pin.

49. Install brake band in transmission case.

CAUTION:

Assemble it so that identification to avoid incorrect installa-
tion faces servo side.

50. Install front sun gear to front carrier assembly.

CAUTION:

Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.

SCIA5015E

SCIA2470E

SCIA6512E

SCIA5498E

SCIA5014E

 

 

 

 

 

 

 

Content   ..  95  96  97  98   ..