Infiniti FX35 / FX45. Manual - part 73

AT-220

< SERVICE INFORMATION >

ON-VEHICLE SERVICE

3.

Connect TCM connectors.

4.

Install O-ring in A/T assembly harness connector.

CAUTION:

• Do not reuse O-ring.
• Apply ATF to O-ring.

5.

Install A/T fluid temperature sensor 2 to bracket.

6.

Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM, and then tighten A/T fluid temperature sensor 2
mounting bolt to the specified torque. Refer to "COMPO-
NENTS".

CAUTION:

Adjust bolt hole of bracket to bolt hole of control valve with
TCM.

7.

Install control valve with TCM in transmission case.

CAUTION:

• Make sure that turbine revolution sensor securely installs

turbine revolution sensor hole.

• Hang down revolution sensor harness toward outside so

as not to disturb installation of control valve with TCM.

• Adjust A/T assembly harness connector of control valve

with TCM to terminal hole of transmission case.

SCIA5447E

SCIA5155E

SCIA5264E

SCIA5301E

SCIA5034E

ON-VEHICLE SERVICE

AT-221

< SERVICE INFORMATION >

D

E

F

G

H

I

J

K

L

M

A

B

AT

N

O

P

• Assemble it so that manual valve cutout is engaged with

manual plate projection.

8.

Install bolts A, B and C in control valve with TCM.
•

: Vehicle front        

9.

Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1 

→

 2 

→

 3), and then tighten other

bolts to the specified torque. Refer to "COMPONENTS".
•

: Vehicle front

10. Connect A/T fluid temperature sensor 2 connector (1).

11. Securely fasten terminal cord assembly and A/T fluid tempera-

ture sensor 2 harness with terminal clips (

).

SCIA5142E

Bolt symbol

Length mm (in)

Number of bolts

A

42 (1.65)

5

B

55 (2.17)

6

C

40 (1.57)

1

SCIA8074E

SCIA8075E

SCIA8069E

AT-222

< SERVICE INFORMATION >

ON-VEHICLE SERVICE

12. Connect revolution sensor connector.

13. Securely fasten revolution sensor harness with terminal clip.

14. Install magnets in oil pan.

15. Install oil pan to transmission case.

a.

Install oil pan gasket to oil pan.

CAUTION:

• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
• Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.

b.

Install oil pan (3) (with oil pan gasket), clips (2) and brackets (1)
(VK45DE) to transmission case.
•

: Vehicle front 

•

: Bolt (22)

CAUTION:

• Install it so that drain plug (4) comes to the position as

shown in the figure.

• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.

from oil pan mounting surface.

SCIA7524E

SCIA7525E

SCIA5200E

SCIA8128E

ON-VEHICLE SERVICE

AT-223

< SERVICE INFORMATION >

D

E

F

G

H

I

J

K

L

M

A

B

AT

N

O

P

c.

Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to "COMPONENTS".

CAUTION:

Do not reuse oil pan mounting bolts.

16. Install drain plug to oil pan, and then tighten drain plug to the

specified torque. Refer to "COMPONENTS".

CAUTION:

Do not reuse drain plug gasket.

17. Pull up A/T assembly harness connector.

CAUTION:

Be careful not to damage connector.

18. Install snap ring to A/T assembly harness connector.

19. Connect A/T assembly harness connector.

20. Connect heated oxygen sensor 2 harness connector.
21. Install front cross bar. Refer to 

FSU-6, "Removal and Installa-

tion"

.

22. Pour ATF into A/T assembly. Refer to 

AT-11, "Changing A/T

Fluid"

.

23. Connect the battery cable to the negative terminal.

A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION

Removal

1.

Disconnect the battery cable from the negative terminal.

2.

Remove front cross bar. Refer to 

FSU-6, "Removal and Installation"

.

3.

Disconnect heated oxygen sensor 2 harness connector.

4.

Drain ATF through drain plug.

5.

Remove bracket (1) (VK45DE), clips (2), oil pan (3) and oil pan
gasket.
•

: Vehicle front

•

: Bolt (22)

• Drain plug (4)

SCIA4113E

SCIA5038E

SCIA5039E

SCIA8128E