Infiniti FX35, FX50 (S51). Manual - part 893

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  891  892  893  894   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 893

 

 

ICC BRAKE SWITCH

EC-1113

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

3.

Check the continuity between ICC brake hold relay terminals
under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ICC brake hold relay

Terminals

Condition

Continuity

3 and 4

12 V direct current supply between terminals 1 and 2

Not existed

No current supply

Existed

6 and 7

12 V direct current supply between terminals 1 and 2

Existed

No current supply

Not existed

MBIB0063E

EC-1114

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

IGNITION SIGNAL

IGNITION SIGNAL

Description

INFOID:0000000005237620

The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor turns
ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil
secondary circuit.

Component Function Check

INFOID:0000000005237621

1.

INSPECTION START

Turn ignition switch OFF, and restart engine.

Does the engine start?

YES-1 >> With CONSULT-III: GO TO 2.
YES-2 >> Without CONSULT-III: GO TO 3.
NO

>> Go to 

EC-1114, "Diagnosis Procedure"

.

2.

CHECK IGNITION SIGNAL FUNCTION

 With CONSULT-III

1.

Perform “POWER BALANCE” in “ACTIVE TEST” mode with CONSULT-III.

2.

Check that each circuit produces a momentary engine speed drop.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-1114, "Diagnosis Procedure"

.

3.

CHECK IGNITION SIGNAL FUNCTION

 Without CONSULT-III

1.

Let engine idle.

2.

Read the voltage signal between ECM harness connector terminals under the following conditions with an
oscilloscope.

NOTE:

The pulse cycle changes depending on rpm at idle.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-1114, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005237622

1.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-I

1.

Turn ignition switch OFF, wait at least 10 seconds and then turn it ON.

2.

Check the voltage between ECM harness connector terminals under the following conditions.

ECM

Voltage signal

Cylinder

+

Connector

Terminal

Connector

Terminal

1

F110

10

M160

128

2

9

3

13

4

14

5

18

6

22

7

26

8

30

PBIB0044E

IGNITION SIGNAL

EC-1115

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Go to 

EC-736, "Diagnosis Procedure"

.

2.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II

1.

Turn ignition switch OFF.

2.

Disconnect condenser harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between condenser harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 3.

3.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-III

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R harness connector E7.

3.

Check the continuity between IPDM E/R harness connector and condenser harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> Go to 

EC-736, "Diagnosis Procedure"

.

NO

>> GO TO 4.

4.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E10, F10
• Harness for open or short between IPDM E/R and condenser

>> Repair open circuit, short to ground or short to power in harness or connectors.

5.

CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Check the continuity between condenser harness connector and ground.

3.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair open circuit or short to power in harness or connectors.

ECM

Voltage

Connector

+

Terminal

Terminal

M160

121

128

Battery voltage

Condenser

Ground

Voltage

Connector

Terminal

F8

1

Ground

Battery voltage

IPDM E/R

Condenser

Continuity

Connector

Terminal

Connector

Terminal

E7

49

F8

1

Existed

Condenser

Ground

Continuity

Connector

Terminal

F8

2

Ground

Existed

EC-1116

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

IGNITION SIGNAL

6.

CHECK CONDENSER

Refer to 

EC-1118, "Component Inspection (Condenser)"

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace condenser.

7.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IV

1.

Reconnect all harness connectors disconnected.

2.

Disconnect ignition coil harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between ignition coil harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> GO TO 8.

8.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connector F10
• Harness for open or short between ignition coil and harness connector F10

>> Repair or replace harness or connectors.

9.

CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Check the continuity between ignition coil harness connector and ground.

3.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 10.

Ignition coil

Ground

Voltage

Cylinder

Connector

Terminal

1

F75

3

Ground

Battery voltage

2

F76

3

3

F77

3

4

F78

3

5

F79

3

6

F80

3

7

F81

3

8

F82

3

Ignition coil

Ground

Continuity

Cylinder

Connector

Terminal

1

F75

2

Ground

Existed

2

F76

2

3

F77

2

4

F78

2

5

F79

2

6

F80

2

7

F81

2

8

F82

2

 

 

 

 

 

 

 

Content   ..  891  892  893  894   ..