Infiniti FX35, FX50 (S51). Manual - part 874

P1554 BATTERY CURRENT SENSOR

EC-1037

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

2.

PERFORM COMPONENT FUNCTION CHECK

 With CONSULT-III

1.

Start engine and let it idle.

2.

Select “BAT CUR SEN” in “DATA MONITOR” mode with CONSULT-III.

3.

Check “BAT CUR SEN” indication for 10 seconds.
“BAT CUR SEN” should be above 2,300 mV at least once.

 Without CONSULT-III

1.

Start engine and let it idle.

2.

Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-1037, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005237530

1.

CHECK GROUND CONNECTION

1.

Turn ignition switch OFF.

2.

Check ground connection M95. Refer to Ground Inspection in 

GI-39, "Circuit Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ground connection.

2.

CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-I

1.

Disconnect battery current sensor harness connector.

2.

Turn ignition switch ON.

3.

Check the voltage between battery current sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> GO TO 3.

3.

CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-II

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between battery current sensor harness connector and ECM harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

DETECT MALFUNCTIONING PART

ECM

Voltage (V)

Connector

+

–

Terminal

Terminal

F111

76

(Battery current sensor signal)

70

Above 2.3 at least once

Battery current sensor

Ground

Voltage (V)

Connector

Terminal

E21

1

Ground

Approx. 5

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

1

F111

95

Existed

EC-1038

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

P1554 BATTERY CURRENT SENSOR

Check the following.
• Harness connectors F10, E10
• Harness for open between battery current sensor and ECM

>> Repair open circuit.

5.

CHECK SENSOR POWER SUPPLY CIRCUIT

Check harness for short to power and short to ground, between the following terminals.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair short to ground or short to power in harness or connectors.

6.

CHECK COMPONENTS

Check the following.
• Crankshaft position sensor (Refer to 

EC-876, "Component Inspection"

.)

• Camshaft position sensor (bank 1) (Refer to 

EC-881, "Component Inspection"

.)

• Exhaust valve timing control position sensor (bank 1) (Refer to 

EC-978, "Component Inspection"

.)

• EVAP control system pressure sensor (Refer to 

EC-917, "Component Inspection"

.)

• Manifold absolute pressure sensor (Refer to 

EC-785, "Component Inspection"

.)

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace malfunctioning component.

7.

CHECK APP SENSOR

Refer to 

EC-1081, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> GO TO 8.

8.

REPLACE ACCELERATOR PEDAL ASSEMBLY

1.

Replace accelerator pedal assembly.

2.

Perform 

EC-1082, "Special Repair Requirement"

.

>> INSPECTION END

9.

CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between battery current sensor harness connector and ECM harness connector.

ECM

Sensor

Connector

Terminal

Name

Connector

Terminal

F111

87

Crankshaft position sensor

F2

1

91

Camshaft position sensor (bank 1)

F84

1

EVT control position sensor (bank 1)

F59

1

95

Battery current sensor

E21

1

EVAP control system pressure sensor

B252

3

Manifold absolute pressure sensor

F65

1

M160

99

APP sensor (Without ICC)

E112

6

APP sensor (with ICC)

E116

3

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

2

F111

70

Existed

P1554 BATTERY CURRENT SENSOR

EC-1039

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> GO TO 10.

10.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors F10, E10
• Harness for open or short between battery current sensor and ECM

>> Repair open circuit, short to ground or short to power in harness or connectors.

11.

CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check the continuity between battery current sensor harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 13.

NO

>> GO TO 12.

12.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors F10, E10
• Harness for open or short between battery current sensor and ECM

>> Repair open circuit, short to ground or short to power in harness or connectors.

13.

CHECK BATTERY CURRENT SENSOR

Refer to 

EC-1039, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 14.

NO

>> Replace battery negative cable assembly.

14.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-36, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000005237531

1.

CHECK BATTERY CURRENT SENSOR

1.

Turn ignition switch OFF.

2.

Reconnect harness connectors disconnected.

Battery current sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E21

3

F111

76

Existed

EC-1040

< DTC/CIRCUIT DIAGNOSIS >

[VK50VE]

P1554 BATTERY CURRENT SENSOR

3.

Disconnect battery negative cable (1).

4.

Install jumper cable (A) between battery negative terminal and
body ground.

5.

Turn ignition switch ON.

6.

Check the voltage between ECM harness connector terminals
under the following conditions.

Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to 

PG-3, "How to Handle Battery"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace battery negative cable assembly.

: To body ground

ECM

Voltage (V)

Connector

+

–

Terminal

Terminal

F111

76

(Battery current sensor signal)

70

Approx. 2.5

JMBIA1512ZZ