Infiniti FX35, FX50 (S51). Manual - part 710

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  708  709  710  711   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 710

 

 

P1233, P2101 ELECTRIC THROTTLE CONTROL FUNCTION

EC-381

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P1233, P2101 ELECTRIC THROTTLE CONTROL FUNCTION

Description

INFOID:0000000005236978

Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor. The throttle position
sensor provides feedback to the ECM, when open/closes the throttle valve in response to driving conditions
via the throttle control motor.

DTC Logic

INFOID:0000000005236979

DTC DETECTION LOGIC

NOTE:
If DTC P1233 or P2101 is displayed with DTC P1238, P2119, first perform the trouble diagnosis for DTC
P1238, P2119. Refer to 

EC-388, "DTC Logic"

.

If DTC P2101 or P2101 is displayed with DTC P1290, P2100, first perform the trouble diagnosis for DTC
P1290, P2100. Refer to 

EC-393, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.

Turn ignition switch OFF and wait at least 10 seconds.

2.

Turn ignition switch ON.

3.

Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V when
engine is running.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 2 seconds.

2.

Start engine and let it idle for 5 seconds.

3.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-381, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005236980

1.

CHECK GROUND CONNECTION

1.

Turn ignition switch OFF.

2.

Check ground connection M95. Refer to Ground Inspection in 

GI-39, "Circuit Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ground connection.

2.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I

Check the voltage between ECM harness connector terminals as follows.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1233

Electric throttle control 
performance (bank 2)

Electric throttle control function does not oper-
ate properly.

• Harness or connectors

(Throttle control motor circuit is open or 
shorted)

• Electric throttle control actuator

P2101

Electric throttle control 
performance (bank 1)

EC-382

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P1233, P2101 ELECTRIC THROTTLE CONTROL FUNCTION

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> GO TO 3.

3.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Disconnect IPDM E/R harness connector E7.

4.

Check the continuity between IPDM E/R harness connector and ECM harness connector.

5.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E3, F1
• Harness connectors F104, F105
• Harness for open or short between ECM and IPDM E/R

>> Repair open circuit, short to ground or short to power in harness or connectors.

5.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II

1.

Check the continuity between IPDM E/R harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 6.

6.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E3, F1
• Harness for open or short between ECM and IPDM E/R

>> Repair open circuit, short to ground or short to power in harness or connectors.

DTC

ECM

Condition

Voltage (V)

+

Connector

Terminal

Connector

Terminal

P1233

F102

52

M107

128

Ignition switch OFF

Approx. 0

Ignition switch ON

Battery voltage

P2101

F101

3

Ignition switch OFF

Approx. 0

Ignition switch ON

Battery voltage

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E7

70

F101

25

Existed

DTC

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

P1233

E7

54

F102

52

Existed

P2101

F101

3

P1233, P2101 ELECTRIC THROTTLE CONTROL FUNCTION

EC-383

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

7.

CHECK FUSE

1.

Disconnect 15 A fuse (No. 51) from IPDM E/R.

2.

Check if 15 A fuse is blown.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace 15 A fuse.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-36, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness or connectors.

9.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORT

1.

Turn ignition switch OFF.

2.

Disconnect electric throttle control actuator harness connector.

3.

Disconnect ECM harness connector.

4.

Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.

5.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning part.

10.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY 

1.

Remove the intake air duct.

2.

Check if foreign matter is caught between the throttle valve (1)
and the housing.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Remove the foreign matter and clean the electric throttle

control actuator inside.

11.

CHECK THROTTLE CONTROL MOTOR

Refer to 

EC-384, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> GO TO 13.

DTC

Electric throttle control actuator

ECM

Continuity

Bank

Connector

Terminal

Connector

Terminal

P1233

2

F27

5

F102

49

Existed

50

Not existed

6

49

Not existed

50

Existed

P2101

1

F6

1

F101

2

Existed

4

Not  existed

2

2

Not  existed

4

Existed

JMBIA1511ZZ

EC-384

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P1233, P2101 ELECTRIC THROTTLE CONTROL FUNCTION

12.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-36, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> GO TO 13.

NO

>> Repair or replace harness or connectors.

13.

REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1.

Replace malfunction electric throttle control actuator.

2.

Go to 

EC-384, "Special Repair Requirement"

.

>> INSPECTION END

Component Inspection

INFOID:0000000005236981

1.

CHECK THROTTLE CONTROL MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect electric throttle control actuator harness connector.

3.

Check resistance between electric throttle control actuator terminals as follows.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1.

Replace malfunctioning electric throttle control actuator.

2.

Go to 

EC-384, "Special Repair Requirement"

.

>> INSPECTION END

Special Repair Requirement

INFOID:0000000005236982

1.

PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Refer to 

EC-25, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"

>> GO TO 2.

2.

PERFORM IDLE AIR VOLUME LEARNING

Refer to 

EC-25, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"

>> END

Electric throttle control actuator

Resistance

Bank

Terminals

1

1 and 2

Approx. 1 - 15 

 [at 25

°

C (77

°

F)]

2

5 and 6

 

 

 

 

 

 

 

Content   ..  708  709  710  711   ..