Infiniti FX35, FX50 (S51). Manual - part 659

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  657  658  659  660   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 659

 

 

P0102, P0103, P010C, P010D MAF SENSOR

EC-177

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

6.

CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between MAF sensor harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair open circuit, short to ground or short to power in harness or connectors.

7.

CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check the continuity between MAF sensor harness connector and ECM harness connector.

2.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair open circuit, short to ground or short to power in harness or connectors.

8.

CHECK MAF SENSOR

Refer to 

EC-177, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace malfunctioning mass air flow sensor.

9.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-36, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000005236777

1.

CHECK MASS AIR FLOW (MAF) SENSOR-I

With CONSULT-III

1.

Turn ignition switch OFF.

2.

Reconnect all harness connectors disconnected.

3.

Start engine and warm it up to normal operating temperature.

4.

Connect CONSULT-III and select “DATA MONITOR” mode.

5.

Select “MAS A/F SE-B1” and “MAS A/F SE-B2”, and check the indication.

DTC

MAF sensor

ECM

Continuity

Bank

Connector

Terminal

Connector

Terminal

P0102, P0103

1

F31

4

F102

68

Existed

P010C, P010D

2

F42

4

94

DTC

MAF sensor

ECM

Continuity

Bank

Connector

Terminal

Connector

Terminal

P0102, P0103

1

F31

3

F102

77

Existed

P010C, P010D

2

F42

3

79

Monitor item

Condition

Indication (V)

MAS A/F SE-B1
MAS A/F SE-B2

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operating temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

EC-178

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P0102, P0103, P010C, P010D MAF SENSOR

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Without CONSULT-III

1.

Turn ignition switch OFF.

2.

Reconnect all harness connectors disconnected.

3.

Start engine and warm it up to normal operating temperature.

4.

Check the voltage between ECM harness connector terminals under the following conditions.

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> GO TO 2.

2.

CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MAF SENSOR

1.

Turn ignition switch OFF.

2.

Check for the cause of uneven air flow through MAF sensor. Refer to the following.

-

Crushed air ducts

-

Malfunctioning seal of air cleaner element

-

Uneven dirt of air cleaner element

-

Improper specification of intake air system parts

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK MAF SENSOR-II

With CONSULT-III

1.

Repair or replace malfunctioning part.

2.

Start engine and warm it up to normal operating temperature.

3.

Connect CONSULT-III and select “DATA MONITOR” mode.

4.

Select “MAS A/F SE-B1” and “MAS A/F SE-B2”, and check the indication.

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Without CONSULT-III

1.

Repair or replace malfunctioning part.

2.

Start engine and warm it up to normal operating temperature.

ECM

Condition

Voltage (V)

Connector

+

Terminal

Terminal

F102

77

[MAF sensor (bank 1) 

signal]

68

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

79

[MAF sensor (bank 2) 

signal]

94

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

Monitor item

Condition

Indication (V)

MAS A/F SE-B1
MAS A/F SE-B2

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operating temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

P0102, P0103, P010C, P010D MAF SENSOR

EC-179

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

3.

Check the voltage between ECM harness connector terminals under the following conditions.

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

CHECK MAF SENSOR-III

With CONSULT-III

1.

Turn ignition switch OFF.

2.

Disconnect MAF sensor harness connector and reconnect it again.

3.

Start engine and warm it up to normal operating temperature.

4.

Connect CONSULT-III and select “DATA MONITOR” mode.

5.

Select “MAS A/F SE-B1” and “MAS A/F SE-B2”, and check the indication.

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Without CONSULT-III

1.

Turn ignition switch OFF.

2.

Disconnect MAF sensor harness connector and reconnect it again.

3.

Start engine and warm it up to normal operating temperature.

4.

Check the voltage between ECM harness connector terminals under the following conditions.

ECM

Condition

Voltage (V)

Connector

+

Terminal

Terminal

F102

77

[MAF sensor (bank 1) 

signal]

68

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

79

[MAF sensor (bank 2) 

signal]

94

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

Monitor item

Condition

Indication (V)

MAS A/F SE-B1
MAS A/F SE-B2

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operating temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

EC-180

< DTC/CIRCUIT DIAGNOSIS >

[VQ35HR]

P0102, P0103, P010C, P010D MAF SENSOR

*: Check for linear voltage rise in response to engine being increased to approximately 4,000 rpm.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Clean or replace malfunctioning MAF sensor.

ECM

Condition

Voltage (V)

Connector

+

Terminal

Terminal

F102

77

[MAF sensor (bank 1) 

signal]

68

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

79

[MAF sensor (bank 2) 

signal]

94

Ignition switch ON (Engine stopped.)

Approx. 0.4

Idle (Engine is warmed-up to normal operat-
ing temperature.)

0.8 - 1.1

2,500 rpm (Engine is warmed-up to normal 
operating temperature.)

1.4 - 1.7

Idle to approx. 4,000 rpm

0.8 - 1.1 to approx. 2.4*

 

 

 

 

 

 

 

Content   ..  657  658  659  660   ..