Infiniti FX35, FX50 (S51). Manual - part 535

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  533  534  535  536   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 535

 

 

BACK DOOR

DLK-263

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR HINGE : Exploded View

INFOID:0000000005239752

BACK DOOR HINGE : Removal and Installation

INFOID:0000000005239753

REMOVAL

1.

Remove luggage side lower finisher and luggage side upper finisher. Refer to 

INT-29, "Removal and

Installation"

.

2.

Using a remover tool, remove headlining clip at the rear side of headlining, and then remove rear side of
headlining. Refer to 

INT-24, "Removal and Installation"

.

3.

Remove back door assembly. Refer to 

DLK-260, "BACK DOOR ASSEMBLY : Removal and Installation"

4.

Remove back door hinge mounting nuts (body side), and then remove back door hinge.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to 

DLK-261, "BACK DOOR ASSEMBLY :

Adjustment"

.

1.

Back door hinge cover (LH/RH)

2.

Back door hinge (LH/RH)

3.

Back door stay bracket (LH/RH)

4.

Back door stay (LH/RH)

5.

Back door weather-strip

6.

Stud ball (LH/RH)

7.

Bumper rubber (side) (LH/RH)

8.

Back door striker

9.

Back door lock assembly

10. Back door assembly

A

:  Center  mark

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2642GB

DLK-264

< REMOVAL AND INSTALLATION >

BACK DOOR

• After installation, perform the camera image calibration. Refer to 

AV-245, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Work Procedure"

 (single monitor) or 

AV-462, "CALIBRATING

CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure"

 (twin monitor).

BACK DOOR STAY

BACK DOOR STAY : Exploded View

INFOID:0000000005239754

BACK DOOR STAY : Removal and Installation

INFOID:0000000005239755

REMOVAL

1.

Support back door lock with the proper material to prevent it from falling.

WARNING:

Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.

2.

Remove mounting bolts of back door stay (body side).

1.

Back door hinge cover (LH/RH)

2.

Back door hinge (LH/RH)

3.

Back door stay bracket (LH/RH)

4.

Back door stay (LH/RH)

5.

Back door weather-strip

6.

Stud ball (LH/RH)

7.

Bumper rubber (side) (LH/RH)

8.

Back door striker

9.

Back door lock assembly

10. Back door assembly

A

:  Center  mark

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2642GB

BACK DOOR

DLK-265

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Remove the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) (back door side) by
using a flat-bladed screwdriver (A).

4.

Remove back door stay (back door side).

5.

Remove mounting bolts of back door stay bracket, and then remove stud ball assembly. 

INSTALLATION

Install in the reverse order of removal.

CAUTION:

After installation, check back door open/close operation.

BACK DOOR WEATHER-STRIP

BACK DOOR WEATHER-STRIP : Exploded View

INFOID:0000000005239756

JMKIA2255ZZ

1.

Back door hinge cover (LH/RH)

2.

Back door hinge (LH/RH)

3.

Back door stay bracket (LH/RH)

4.

Back door stay (LH/RH)

5.

Back door weather-strip

6.

Stud ball (LH/RH)

7.

Bumper rubber (side) (LH/RH)

8.

Back door striker

9.

Back door lock assembly

10. Back door assembly

A

:  Center  mark

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2642GB

DLK-266

< REMOVAL AND INSTALLATION >

BACK DOOR

BACK DOOR WEATHER-STRIP : Removal and Installation

INFOID:0000000005239757

REMOVAL

Pull up and remove engagement with body from weather-strip joint.

CAUTION:

Never pull strongly on weather-strip.

INSTALLATION

1.

Working from the upper section, align weather-strip center mark with vehicle center position mark and
install weather-strip onto the vehicle.

2.

Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Check that weather-strip fits tightly in each corner and luggage rear plate.

 

 

 

 

 

 

 

Content   ..  533  534  535  536   ..