Infiniti FX35, FX50 (S51). Manual - part 300

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  298  299  300  301   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 300

 

 

CCS-20

< BASIC INSPECTION >

[ICC (FULL SPEED RANGE)]

INSPECTION AND ADJUSTMENT

4.

Push down the SET/COAST switch. 

5.

Check that the desired speed is set and vehicle-to-vehicle distance control mode control starts when
releasing SET/COAST switch.

NOTE:
The set vehicle speed is indicated on the set vehicle speed indicator in the ICC system display on the informa-
tion display. 

>> GO TO 5.

5.

CHECK FOR INCREASE OF CRUISING SPEED (1)

1.

Set the vehicle-to-vehicle distance control mode at desired speed.

2.

Check that the set speed increases by 1 km/h (1 MPH) as RESUME/ACCELERATE switch is pushed up.

NOTE:
The maximum set speed of the vehicle-to-vehicle distance control mode is 144 km/h (90 MPH).

CAUTION:

Never set the cruise speed exceeding the posted speed limit.

>> GO TO 6.

6.

CHECK FOR DECREASE OF CRUISING SPEED (1)

1.

Set the vehicle-to-vehicle distance control mode at desired speed. 

2.

Check that the set speed decreases by 1 km/h (1 MPH) as SET/COAST switch is pushed down.

NOTE:
• The minimum set speed is approximately 32 km/h (20 MPH).
• Cancel the control automatically when the vehicle speed is less than approximately 24 km/h (15 MPH) and

when the system does not detect any vehicle ahead. 

>> GO TO 7.

7.

SET CHECKING (2)

1.

Stop the vehicle.

2.

Drive the vehicle at less than approximately 32 km/h (20 MPH). 

3.

Push down the SET/COAST switch when the system detects a vehicle ahead. 

4.

Check that the vehicle-to-vehicle distance control mode is performed so that the vehicle maintains a
proper distance according to the vehicle speed [maximum: approximately 32 km/h (20 MPH)] when
releasing SET/COAST switch. 

NOTE:
• The vehicle-to-vehicle distance control mode cannot be set when the vehicle speed is less than 32 km/h (20

MPH) and when a vehicle ahead is not detected. 

• Cancel the control automatically when the vehicle speed is 24 km/h (15 MPH) or less during the control and

when the system does not detect any vehicle ahead. 

• The set vehicle speed indicator in the ICC system display on the information display is set to 32 km/h (20

MPH).

>> GO TO 8.

8.

CHECK FOR INCREASE OF CRUISING SPEED (2)

1.

Set the vehicle-to-vehicle distance control mode when the vehicle speed is less than approximately 32
km/h (20 MPH) and when a vehicle ahead is detected. 

2.

Check that the set speed increases by 1 km/h (1 MPH) as RESUME/ACCELERATE switch is pushed up.

NOTE:
The maximum set speed of the vehicle-to-vehicle distance control mode is 144 km/h (90 MPH).

CAUTION:

Never set the cruise speed exceeding the posted speed limit.

>> GO TO 9.

9.

CHECK FOR DECREASE OF CRUISING SPEED INSPECTION (2)

CCS

INSPECTION AND ADJUSTMENT

CCS-21

< BASIC INSPECTION >

[ICC (FULL SPEED RANGE)]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

1.

Set the vehicle-to-vehicle distance control mode when the vehicle speed is less than approximately 32
km/h (20 MPH) and when a vehicle ahead is detected. 

2.

Set the set vehicle speed to the desired vehicle speed according to “check for increase of cruising speed”. 

3.

Check that the set speed decreases by 1 km/h (1 MPH) as SET/COAST switch is pushed down.

NOTE:
• The minimum the set speed is approximately 32 km/h (20 MPH).
• If the vehicle ahead comes to a stop, the vehicle decelerates to a standstill within the limitations of the sys-

tem. The system will cancel once it judges a standstill with a warning chime. 

CAUTION:

The creep occurs because the stop status is not maintained. 

>> GO TO 10.

10.

CHECK FOR CANCELLATION OF VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

Check that the vehicle-to-vehicle distance control mode is canceled when performing the following operations. 
• When the brake pedal is depressed after vehicle-to-vehicle distance control mode is set and the vehicle is

driven. 

• When the selector lever is in the “N” position after vehicle-to-vehicle distance control mode is set and the

vehicle is driven. 

• When the MAIN switch is turned OFF after vehicle-to-vehicle distance control mode is set and the vehicle is

driven. 

• When the CANCEL switch is pressed after vehicle-to-vehicle distance control mode is set and the vehicle is

driven. 

>> GO TO 11.

11.

CHECK FOR RESTORING SPEED THAT IS SET BY VEHICLE-TO-VEHICLE DISTANCE CONTROL

MODE BEFORE CANCELLATION

Check that the vehicle restores the previous speed kept before the system deactivation when performing the
following operations. 
• Drive the vehicle when the vehicle-to-vehicle distance control mode is set and depress the brake pedal to

cancel the control. Check that the vehicle restores the previous vehicle speed kept before the system deac-
tivation when pushing up the RESUME/ACCELERATE switch. 

• Drive the vehicle when the vehicle-to-vehicle distance control mode is set and shift the selector lever to the

“N” position to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the
system deactivation when shifting the selector lever to the “D” position and pushing up the RESUME/
ACCELERATE switch.

• Drive the vehicle when the vehicle-to-vehicle distance control mode is set and press the CANCEL switch to

cancel the control. Check that the vehicle restores the previous vehicle speed kept before the system deac-
tivation when pushing up the RESUME/ACCELERATE switch. 

>> INSPECTION END

ACTION TEST : Special Repair Requirement [Conventional (Fixed Speed) Cruise 
Control Mode]

INFOID:0000000005501558

NOTE:
The running speed can be set between 40 km/h (25 MPH) and 144 km/h (90 MPH).

CAUTION:

Never set the cruise speed exceeding the posted speed limit.

1.

CHECK FOR MAIN SWITCH

1.

Start the engine.

CCS-22

< BASIC INSPECTION >

[ICC (FULL SPEED RANGE)]

INSPECTION AND ADJUSTMENT

2.

Press the MAIN switch (1) (1.5 seconds or more). 

3.

Check that the ICC system display on the information display turns on and the display is ready for activa-
tion. 

4.

Press the MAIN switch, and check that the ICC system display on the information display turns OFF when
the ICC system is deactivated.

5.

Check that the ICC system display on the information display turns OFF after starting the engine again. 

>> GO TO 2.

2.

CHECK FOR RESUME/ACCELERATE, SET/COAST, AND CANCEL SWITCHES

1.

Check that RESUME/ACCELERATE, SET/COAST, CANCEL switches are operated smoothly.

2.

Check that switches come up as hand is released from the switches.

>> GO TO 3.

3.

SET CHECKING

1.

Start the engine.

2.

Press the MAIN switch (1.5 seconds or more) and turn the conventional (fixed speed) cruise control mode
to ON. 

3.

Drive the vehicle at 40 km/h (25 MPH) or more. 

4.

Push down the SET/COAST switch. 

5.

Check that the desired speed is set and conventional (fixed speed) cruise control mode control starts
when releasing SET/COAST switch. 

NOTE:
• The set vehicle speed is not displayed in the ICC system display on the information display. 
• Display the set status in the ICC system display on the information display. 

>> GO TO 4.

4.

CHECK FOR INCREASE OF CRUISING SPEED

1.

Set the vehicle speed to any desired speed, and drive the vehicle.

2.

Check that the set speed increases by 1.6 km/h (1 MPH) as RESUME/ACCELERATE switch is pushed
up. 

NOTE:
• The maximum set speed is 144 km/h (90 MPH).
• The set vehicle speed increases while pushing up the RESUME/ACCELERATE switch.

CAUTION:

Never set the cruise speed exceeding the posted speed limit.

>> GO TO 5.

5.

CHECK FOR DECREASE OF CRUISING SPEED

1.

Set the vehicle speed to any desired speed, and drive the vehicle.

2.

Check that the set speed decreases by 1.6 km/h (1 MPH) as SET/COAST switch is pushed down.

NOTE:
• The minimum set speed is 40 km/h (25 MPH).
• The set vehicle speed decreases while pressing down the SET/COAST switch. 

Information display status

MAIN switch indicator (2)

: ON

JSOIA0149ZZ

CCS

INSPECTION AND ADJUSTMENT

CCS-23

< BASIC INSPECTION >

[ICC (FULL SPEED RANGE)]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

• Cancel the control automatically when the vehicle speed lowers to less than approximately 32 km/h (20

MPH). 

>> GO TO 6.

6.

CHECK FOR CANCELLATION OF CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE

Check that the conventional (fixed speed) cruise control mode is canceled when performing the following
operations. 
• When the brake pedal is depressed after the conventional (fixed speed) cruise control mode is set and the

vehicle is driven. 

• When the selector lever is in the “N” position after the conventional (fixed speed) cruise control mode is set

and the vehicle is driven. 

• When the MAIN switch is turned OFF after the conventional (fixed speed) cruise control mode is set and the

vehicle is driven. 

• When the CANCEL switch is pressed after the conventional (fixed speed) cruise control mode is set and the

vehicle is driven. 

>> GO TO 7.

7.

CHECK FOR RESTORING SPEED THAT IS SET BY CONVENTIONAL (FIXED SPEED) CRUISE CON-

TROL MODE BEFORE CANCELLATION

Check that the vehicle restores the previous speed kept before the system deactivation when performing the
following operations. 
• Drive the vehicle when the conventional (fixed speed) cruise control mode is set and depress the brake

pedal to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the sys-
tem deactivation when pushing up the RESUME/ACCELERATE switch at the vehicle speed approximately
40 km/h (25 MPH) or more. 

• Drive the vehicle when the conventional (fixed speed) cruise control mode is set and shift the selector lever

is in the “N” position to cancel the control. Check that the vehicle restores the previous vehicle speed kept
before the system deactivation when shifting the selector lever is in the “D” position and pushing up the
RESUME/ACCELERATE switch at the vehicle speed of approximately 40 km/h (25 MPH) or more. 

• Drive the vehicle when the conventional (fixed speed) cruise control mode is set and press the CANCEL

switch to cancel the control. Check that the vehicle restores the previous vehicle speed kept before the sys-
tem deactivation when pushing up the RESUME/ACCELERATE switch at the vehicle speed of approxi-
mately 40 km/h (25 MPH) or more. 

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  298  299  300  301   ..