Infiniti FX35, FX50 (S51). Manual - part 1737

B1136 SIDE MODULE LH

SRC-113

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1136 SIDE MODULE LH

Description

INFOID:0000000005241196

For front LH side air bag module, crash is judged by main “G” sensor output signal (left side: LH satellite sen-
sor, right side: RH satellite sensor) and safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front LH side air bag module mainly consists of air bag and inflator that inflates air bag.

INSTALLATION

Front LH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000005241197

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-16, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-113, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005241198

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1136

SIDE MODULE LH 
[GND-SHORT]

Front LH side air bag module circuit is 
shorted to ground

• Disconnection of wiring harness and 

short

• Malfunction in front LH side air bag 

module

• Malfunction in air bag diagnosis sen-

sor unit

SRC-114

< DTC/CIRCUIT DIAGNOSIS >

B1136 SIDE MODULE LH

NO

>> Replace wiring harness.

3.

REPLACE FRONT SIDE AIR BAG MODULE

1.

Replace front LH side air bag module. Refer to 

SE-81, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-113, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-25, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-113, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

B1137 SIDE MODULE LH

SRC-115

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1137 SIDE MODULE LH

Description

INFOID:0000000005241199

For front LH side air bag module, crash is judged by main “G” sensor output signal (left side: LH satellite sen-
sor, right side: RH satellite sensor) and safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front LH side air bag module mainly consists of air bag and inflator that inflates air bag.

INSTALLATION

Front LH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000005241200

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-16, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-115, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005241201

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use un specified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1137

SIDE MODULE LH 
[SHORT]

Front LH side air bag module circuit are 
shorted to each other

• Disconnection of wiring harness and 

short

• Malfunction in front LH side air bag 

module

• Malfunction in air bag diagnosis sen-

sor unit

SRC-116

< DTC/CIRCUIT DIAGNOSIS >

B1137 SIDE MODULE LH

NO

>> Replace wiring harness.

3.

REPLACE FRONT SIDE AIR BAG MODULE

1.

Replace front LH side air bag module. Refer to 

SE-81, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-115, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-25, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-115, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END