Infiniti FX35, FX50 (S51). Manual - part 1706

FRONT PASSENGER AIR BAG MODULE

SR-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

FRONT PASSENGER AIR BAG MODULE

Exploded View

INFOID:0000000005249832

Removal and Installation

INFOID:0000000005249833

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.

REMOVAL

1.

Remove the instrument panel assembly. Refer to 

IP-12, "Removal and Installation"

.

2.

Remove the passenger air bag module (1) fixing screws (A).

1.

Passenger air bag module

2.

Instrument panel assembly

: Vehicle front

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMHIA0658GB

JMHIA0659ZZ

SR-18

< REMOVAL AND INSTALLATION >

FRONT PASSENGER AIR BAG MODULE

3.

Disconnect pawls by using remover tool (A), and then remove
the front passenger air bag module (1) from the instrument
panel (2).

CAUTION:

• Always place the passenger air bag module with pad side fac-

ing upward.

• Never impact the passenger air bag module. 
• Replace the passenger air bag module if it has been dropped

or sustained an impact.

• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Never disassemble the passenger air bag module.
• Never expose the passenger air bag module to temperatures exceeding 90

°

C (194

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the passenger air bag module.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Never use the old fixing bolts after removal; replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to 

SRC-20, "CONSULT-III

Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp. 

: Pawl

JMHIA0660ZZ

: Upward

JMHIA0661ZZ

JMHIA0009ZZ

SIDE CURTAIN AIR BAG MODULE

SR-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

SIDE CURTAIN AIR BAG MODULE

Exploded View

INFOID:0000000005249834

Removal and Installation

INFOID:0000000005249835

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use the air tools or the electric tools for servicing.

REMOVAL

1.

Remove the headlining. Refer to 

INT-24, "Removal and Installation"

.

2.

Remove the side curtain air bag module harness connector.

CAUTION:

• For installing/removing the side curtain air bag module

harness connector, insert thin screwdriver wrapped in
tape into notch, lift lock and remove connector.

• Install the connector with lock raised, and push lock into

the connector.

• After installing the connector, check that the lock is

pushed securely into it.

3.

Remove the fixing bolts, and then remove the side curtain air bag module.

CAUTION:

1.

Side curtain air bag module

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMHIA0662GB

PHIA0953J

SR-20

< REMOVAL AND INSTALLATION >

SIDE CURTAIN AIR BAG MODULE

• Never impact the side curtain air bag module.
• Replace the side curtain air bag module if it has been dropped

or sustained an impact. 

• Never insert any foreign objects (screwdriver, etc.) into side curtain air bag module.
• Never disassemble the side curtain air bag module.
• Never expose the side curtain air bag module to temperatures exceeding 90

°

C (194

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to 

SRC-20, "CONSULT-III

Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp. 

JMHIA0009ZZ