Infiniti FX35, FX50 (S51). Manual - part 1644

SE-96

< REMOVAL AND INSTALLATION >

REAR SEAT

Remove the clips.

2.

Remove the armrest assembly. (RH seat only)
• Remove the hog lings, and then pull the seatback trim.
• Remove the metal clips and pawl, and then pull out armrest

bracket cover.

• Remove the mounting bolts (A), and then remove the armrest

bracket (1).

• Remove the armrest assembly.

3.

Remove the reclining device cover.
Remove the screws (A) and clip (B), and then reclining device
inner cover (1) and reclining device inner cover inside (2).

4.

Remove the reclining lever knob assembly.

: Clip

JMJIA2086ZZ

: Metal clip

: Pawl

JMJIA2087ZZ

JMJIA2088ZZ

JMJIA2089ZZ

REAR SEAT

SE-97

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

• Remove the push nut (1), cable resin part (2) and cable clamp

(3).

• Remove the hog rings (A) and cable clamp.

• Remove the reclining lever knob cap.
• Remove the screw (B), and then remove reclining knob lever

assembly (4).

5.

Remove the seatback trim and pad.
• Remove the seatback hinge outer cover.
• Remove the mounting bolt (A) and then remove seatback

hinge.

• Remove the hog rings from back side.
• Remove the seatback retainer.
• Remove the seat belt finisher. Refer to 

SB-11, "SEAT BELT RETRACTOR : Removal and Installation"

.

JMJIA2090ZZ

JMJIA2091ZZ

JMJIA2092ZZ

JMJIA2093ZZ

SE-98

< REMOVAL AND INSTALLATION >

REAR SEAT

• Remove the headrest holder.

CAUTION:

Before installing headrest holder check its orientation.
(front/rear and right/left)

• Remove the seatback trim and pad.
• Remove the hog rings to separate the seatback trim and seatback pad.

6.

Remove the reclining device (LH). (LH seat only)
Remove the mounting bolts (A), and then remove reclining
device (LH).

7.

Remove the dynamic damper.
Remove the dynamic damper mounting nuts (A).

8.

Remove the seat belt hook.

9.

Remove the rear center seat belt retractor. Refer to 

SB-11, "SEAT BELT RETRACTOR : Removal and

Installation"

.

Assembly

Assemble in the reverse order of disassembly.

CAUTION:

• Always slacken cable end and link pin when installing reclin-

ing lever knob cable.

PIIB8351J

JMJIA2322ZZ

JMJIA2094ZZ

JMJIA2320ZZ

REAR SEAT

SE-99

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

• Always install in the position that the reclining device lock

can be released, because cable resin part is adjustable (3
stages).

• Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with

the seatback frame.

SEAT CUSHION

Disassembly

Remove the hog rings to separate the trim and pad.

Assembly

Assemble in the reverse order of disassembly.

CAUTION:

Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the seat cushion pad wire.

ARMREST

Disassembly

1.

Remove the cup holder.
Remove the metal clips and pawls.

2.

Remove the armrest lid assembly.
Remove the mounting screw.

3.

Remove the armrest strap.
• Open the fastener (1), and then pull up armrest trim.

JMJIA2321ZZ

: Pawl

: Metal clip

JMJIA2099ZZ

JMJIA2100ZZ