Infiniti FX35, FX50 (S51). Manual - part 1641

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1639  1640  1641  1642   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 1641

 

 

SE-84

< REMOVAL AND INSTALLATION >

FRONT SEAT

Removal and Installation

INFOID:0000000005236657

REMOVAL

CAUTION:

When removing and installing, use shop cloths to protect parts from damage.

1.

Remove the headrest.

2.

Remove the front slide cover.

a.

Front outer slide cover
• Slide the seat to the rear-most position.
• Pull up the front edge of the front outer slide cover to release

the pawls.

• Slide the front outer slide cover forward to release the pawls.

b.

Front inner slide cover
• Slide the seat to the rear-most position.
• Pull up the front edge of the front inner slide cover to release

the pawls.

• Slide the front inner slide cover forward to release the pawls.

3.

Remove the mounting bolts on the front side of the front seat.

4.

Remove the rear slide cover.

a.

Rear outer slide cover
• Slide the seat to the front-most position.
• Pull up the rear edge of the rear outer slide cover to release

the pawls.

• Slide the rear outer slide cover to release the pawls.

22. Seat cushion outer lower finisher

(inside)

23. Front outer slide cover

24. Seat cushion front finisher

25. Front inner slide cover

26. Seat cushion pad (front)

27. Seat cushion inner lower finisher

28. Seat cushion inner finisher inside 

(rear)

29. Seat cushion inner finisher inside 

(front)

30. Seat cushion inner finisher outside

31. Seat belt buckle

32. Seat cushion pad

33. Seat cushion trim

34. Seatback pad

35. Seatback trim

36. Headrest holder (locked)

37. Headrest holder (free)

38. Headrest

39. Seatback silencer

40. Seatback frame

41. Rear inner slide cover

42. Rear outer slide cover

43. Seat cushion frame

Refer to 

GI-4, "Components"

 for symbols in the figure.

: Pawl

JMJIA2020ZZ

: Pawl

JMJIA2021ZZ

: Pawl

JMJIA2022ZZ

FRONT SEAT

SE-85

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

b.

Rear inner slide cover
• Slide the seat to the front-most position.
• Pull up the rear edge of the rear inner slide cover to release

the pawls.

• Slide the rear inner slide cover rearward to release the pawls.

5.

Remove the mounting bolts on the rear side of the front seat.

6.

Set seatback in a standing position.

7.

Disconnect harness connector under the seat and remove harness securing clips.

CAUTION:

Before removal, turn ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes.

8.

Remove seat from the vehicle.

CAUTION:

• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Before installation, turn ignition switch OFF, disconnect battery negative terminal and then wait for

at least 3 minutes.

• Clamp the harness in position.
NOTE:
• After installing the front seat, perform additional service when removing battery negative terminal (automatic

drive positioner model only). Refer to 

ADP-8, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEG-

ATIVE TERMINAL : Special Repair Requirement"

.

• After installing the passenger seat, perform zero point reset. Refer to 

SRC-8, "ZERO POINT RESET : Spe-

cial Repair Requirement"

.

Disassembly and Assembly

INFOID:0000000005236658

SEATBACK

Disassembly

1.

Remove the seatback board.
• Remove the clips, and then pull out seatback board.
• Pull down the seatback board to release the upper pawls.

2.

Remove the seat cushion outer finisher.

: Pawl

JMJIA2023ZZ

: Clip

: Pawl

JMJIA2024ZZ

SE-86

< REMOVAL AND INSTALLATION >

FRONT SEAT

• Remove the clip, metal clips and pawls, and then pull out seat

cushion outer finisher.

• Remove the connector clamps, and then disconnect harness

connectors.

3.

Remove the seat cushion outer finisher inside (front and rear).

4.

Remove the seat cushion inner finisher.
Remove the metal clip and pawls, and then pull out seat cushion
inner finisher.

5.

Remove the seat cushion inner finisher inside (front and rear).

6.

Remove the seatback trim retainer and seatback trim band from seat cushion frame.

7.

Remove the seatback assembly.
• Remove the side air bag module harness (A).

• Cut the seatback duct band (1) of seat cushion under side.
• Disconnect the side support air hose joint (2).

: Clip

: Metal clip

: Pawl

JMJIA2025ZZ

: Metal clip

: Pawl

JMJIA2026ZZ

JMJIA2027ZZ

JMJIA2028ZZ

FRONT SEAT

SE-87

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

• Disconnect the reclining motor harness connector (B).
• Disconnect the lumbar support unit harness connector (C).
• Disconnect the side support unit harness connector (D).
• Disconnect the seatback thermal electric device (TED) har-

ness connector (E).

• Pull out harness from the seatback trim and seat cushion trim.
• Remove the seatback assembly mounting bolts (F).

8.

Remove the seatback trim and seatback pad.
• Remove the headrest holder.

CAUTION:

Before installing headrest holder check its orientation.
(front/rear and right/left)

• Remove the side air bag module mounting nuts (A).

• Remove the seatback trim and seatback pad from the seatback frame.
• Remove the side air bag module.
• Remove the hog rings, and separate the seatback trim and seatback pad.

9.

Remove the seatback silencer.

10. Remove the seatback side support bag and unit. (Side support model only.)

JMJIA2029ZZ

JMJIA2030ZZ

PIIB8351J

JMJIA2033ZZ

 

 

 

 

 

 

 

Content   ..  1639  1640  1641  1642   ..