Infiniti FX35, FX50 (S51). Manual - part 1550

PWO-10

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000005240724

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

PWO

POWER SOCKET

PWO-11

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

REMOVAL AND INSTALLATION

POWER SOCKET

FRONT POWER SOCKET

FRONT POWER SOCKET : Exploded View

INFOID:0000000005240725

FRONT POWER SOCKET : Removal and Installation

INFOID:0000000005240726

REMOVAL

1.

Remove console pocket assembly. Refer to 

IP-22, "Exploded View"

.

2.

Disconnect power socket connector (A) from reverse side inner
socket (1). 

3.

Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).

4.

Remove ring (2) from console pocket assembly while pressing
pawls.

INSTALLATION

Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console pocket assembly.

CONSOLE POWER SOCKET

1

: Inner socket

2

:  Ring

JPMIA1053ZZ

JPMIA1054ZZ

A

: Cut out

JPMIA1055ZZ

PWO-12

< REMOVAL AND INSTALLATION >

POWER SOCKET

CONSOLE POWER SOCKET : Exploded View

INFOID:0000000005240727

CONSOLE POWER SOCKET : Removal and Installation

INFOID:0000000005240728

REMOVAL

1.

Remove center console assembly. Refer to 

IP-22, "Exploded View"

.

2.

Disconnect power socket connector (A).

3.

Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (D).

4.

Remove ring (2) from console box assembly while pressing
pawls.

INSTALLATION

Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console box assembly.

REAR POWER SOCKET

REAR POWER SOCKET : Exploded View

INFOID:0000000005240729

REAR POWER SOCKET : Removal and Installation

INFOID:0000000005240730

REMOVAL

1.

Remove console rear finisher. Refer to 

IP-22, "Exploded View"

.

1

: Inner socket

2

:  Ring

JPMIA1056ZZ

B

: Cut out

JPMIA1057ZZ

1

: Inner socket

2

:  Ring

JPMIA1058ZZ

PWO

POWER SOCKET

PWO-13

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

2.

Disconnect power socket connector (A).

3.

Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (D).

4.

Remove ring (2) from console rear finisher while pressing pawls.

INSTALLATION

Install in the reverse order of removal.   
NOTE:
Align the cut outs of inner socket, ring, and console rear finisher.

LUGGAGE ROOM POWER SOCKET

LUGGAGE ROOM POWER SOCKET : Exploded View

INFOID:0000000005240731

LUGGAGE ROOM POWER SOCKET : Removal and Installation

INFOID:0000000005240732

REMOVAL

1.

Remove clips on the back of the luggage side finisher lower (RH) to obtain space for work. Refer to 

INT-

28, "Exploded View"

.

2.

Disconnect power socket connector (A).

3.

Remove retainer (1) and remove power socket assembly.

4.

Pull out inner socket (2) by pushing the ring pawl (C) from the
inner socket hole (square) (D).

5.

Remove ring (3) from luggage side finisher lower (RH) while
pressing pawls.

INSTALLATION

Install in the reverse order of removal.   
NOTE:
Align the cut outs of inner socket, ring, and luggage side finisher lower (RH).

B

: Cut out

JPMIA1059ZZ

1

: Inner socket

2

:  Ring

3

:  Retainer

JPMIA1060ZZ

B

: Cut out

JPMIA1061ZZ