Infiniti FX35, FX50 (S51). Manual - part 1253

INT-14

< REMOVAL AND INSTALLATION >

REAR DOOR FINISHER

REAR DOOR FINISHER

Exploded View

INFOID:0000000005240794

Removal and Installation

INFOID:0000000005240795

CAUTION:

Wrap the tip of flat-bladed screwdriver with a cloth before remove.

REMOVAL

1.

Fully open door window.

1.

Rear door panel

2.

Rear door inside handle

3.

Rear door finisher

4.

Rear door center finisher

5.

Inside handle escutcheon

6.

Rear door grip

7.

Rear door grip cap

8.

Step lamp

9.

Power window switch finisher

10. Rear door grip bracket

11. Grommet

: Clip

: Pawl

JMJIA2048ZZ

REAR DOOR FINISHER

INT-15

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

2.

Remove inside handle escutcheon (1) with a flat-bladed screw-
driver (A) wrapped in a tape as shown in the figure.

3.

Insert a remover tool (A) between the rear door grip cap (1) and
the rear door grip to disengage the pawls and remove the cap.

4.

Remove the bolts shown by the arrows in the figure with an
appropriate tool.

5.

Remove the step lamp. Refer to 

INL-192, "Removal and Installation"

.

6.

Insert a remover tool (A) between the door finisher (1) and door
panel to disengage the clips.

CAUTION:

Insert a remover tool into the part show in the figure.
(Between the clips and the door panel)

7.

Disconnect lock knob cable (1) and inside handle cable (2) from
rear inside handle (3).

: Pawl

JMJIA1506ZZ

: Pawl

JMJIA2052ZZ

: Bolt

JMJIA2053ZZ

: Clip

JMJIA2054ZZ

JMJIA1359ZZ

INT-16

< REMOVAL AND INSTALLATION >

REAR DOOR FINISHER

8.

Remove the mood lamp harness connector. Refer to 

INL-190, "REAR DOOR ARMREST : Exploded

View"

.

9.

Disconnect the rear door power window switch harness connector.

10. Remove the rear door finisher.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.

Disassembly and Assembly

INFOID:0000000005240796

DISASSEMBLY

1.

Remove the rear door grip and the rear door center finisher.
NOTE:
The procedure is same as for the front door finisher. Refer to 

INT-13, "Disassembly and Assembly"

.

2.

Remove rear door inside handle. Refer to 

DLK-274, "INSIDE HANDLE : Removal and Installation"

.

ASSEMBLY

Assemble in the reverse order of disassembly.

BODY SIDE TRIM

INT-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

BODY SIDE TRIM

Exploded View

INFOID:0000000005240797

Removal and Installation

INFOID:0000000005240798

CAUTION:

Wrap the tip of flat-bladed screwdriver with a shop cloth when removing metal clips from garnishes.

REMOVAL

FRONT PILLAR GARNISH

1.

Remove front body side welt partially.

1.

Front pillar garnish

2.

Front body side welt

3.

Front kicking plate (outer)

4.

Dash side finisher

5.

Front kicking plate (inner)

6.

Center pillar lower garnish

7.

Rear kicking plate (inner)

8.

Rear body side welt

9.

Rear kicking plate (outer)

10. Center pillar upper garnish

: Clip

: Pawl

: Metal clip

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMJIA2055ZZ